搜索资源列表
at89s8252_spi
- AT89S8252, AT89S53 SPI Program, This program shows how to configure and use the SPI in master mode for the following microcontrollers: ATMEL AT89S53 ATMEL AT89S8252-AT89S8252, AT89S53 SPI Program, This program shows how to configure and use
直流电动机单级性双闭环可逆控制程序
- 用DSP实现直流电动机速度，全部控制程序包括速度PI调节，电流PI调节，PWM控制，主程序进行电机转向的判别-DSP DC motor speed control procedures including full speed PI regulator and current PI regulator, PWM control, the main program for the motor to discriminant
15AHL_PID
- 用28335实现BUCK降压电路的PI调节-Use DSP28335 platform write PI control program to finish BUCK electric circuit
直流电机的速度环PI控制-速度电流检测部分的程序
- 直流电机的速度环PI控制-速度电流检测部分的程序，各部分都已经有了-DC motor speed loop PI control- speed current detection part of the program, all parts have been ~ ~
PI
- 该c程序采用keil c51编写，主要实现对直流电机调速，其中包含转速环PI调节器c代码-The c program using keil c51 prepared, the main achievement of the DC motor speed, including speed loop PI controller c code
motor-PI
- 主要设计了直流电机的速度环PI控制，包括DSM图和C程序-The main design of the DC motor speed loop PI control, including DSM program plans, and C
pi
- How to process an image using a self tested program
sprc128
- 永磁同步电动机无速度传感器程序，其中包含svpwm，电流pi，电压pi等部分-Permanent magnet synchronous motor without a speed sensor program, which includes svpwm, current pi, voltage and some other pi
PiCounter
- This program counts Pi digits
12VVRLAcharger
- 程序是关于12V铅酸蓄电池充电器的。充电方式选择的是普通的三段式，PI调节用硬件实现（其实用软件实现比较好，只是毕业在即时间不够了）。程序主要是判断电池的正反接和充电状态，以便实现三段的切换。对充电器有兴趣的朋友可以参考一下（程序写得不是很标准，将就着看吧）。-Program is on the 12V lead-acid battery charger. Charging an ordinary three-stage selection, PI regulator with the hard
Pi
- PI Assembly Program - which is use for the program development
PI
- Embeded program(processor)
STM8-MC
- 已经用STM8S105调试好的BLDC电机控制程序项目，速度pi调节。-Have STM8S105good debugging BLDC motor control program, PI speed regulation.
PID_control
- 采用DSP的IQ库编写的定点增量式PI调节程序-Using DSP IQ prepared for the fixed-point incremental PI adjustment program
PI
- 直流电机的速度控制，使用pi算法控制。 附上源代码和protues仿真程序。仅供大家 参考-DC motor speed control using pi control algorithm. Attach source code and protues simulation program. For your reference
DSP 28335 TestCode4PI
- dsp28335 PI调节数字化程序代码，调试OK，直接运行，有需要请参考(DSP 28335 PIDigital program code)
testcap
- 基于8257和CodeWarrior平台以及相应功率板的直流无刷电机Pi调节控制程序(Based on the 8257 and CodeWarrior platform and the corresponding power board brushless DC motor control program, you can use freemaster to change the parameters to achieve brushless DC motor PI regulation)
basicsensor.tar
- a basic program to read from the sensors over i2c. I looked at the source code for RTIMULibDrive11 and the datasheets for HTS221 and LPS25H to build the program. Here is the source code for anyone interested (very simple but it gets the job done).
input_control
- 树莓派3b+，通过vnc远程登录后，通过控制台input发送命令控制树莓派程序(Raspberry dispatch 3b +, after remote login through vnc, send commands through console input to control raspberry dispatch program)
MR75020H_PFC
- PFC 无桥PFC全套控制程序代码，维也纳PFC控制代码(PFC no bridge PFC complete control program code, Vienna PFC control code)