搜索资源列表
how_to_change_the_usb_to_uart
- rs232的信息,同时还有usb转串口的一些资料,介绍了一种芯片PL2303.希望能对大家有用-RS232 information, along with usb serial switch some of the information, introduces a PL2303 chip. hope can be useful for all
PL2303的详细原理图
- PL2303的详细原理图,以及外围接口,PDF文档!,PL2303 SCH!
PL2303_WinCE_Driver_src
- Prolific PL-2303 USB to Serial适配器WinCE 5.0驱动源代码-Prolific PL-2303 USB to Serial adapter WinCE 5.0 driver source code
pl2303_PCBlib
- PL2303的封装库(SSOP-28)+PDIUSBD12的封装库(TSSOP-28),在DXP下100 能用,99SE下未测试-PL2303 package library (SSOP-28)+ PDIUSBD12 package library (TSSOP-28), a 100 can be used in DXP, 99SE, has not yet tested
USB-to-RS232-Driver.ZIP
- PL2303芯片通用的USB转串口驱动程序,支持win7,保证可正常使用-PL2303 USB to serial chip universal driver to support win7, guarantee the normal use
usb转串口线 驱动 PL2303
- 这个是usb转串口的驱动,其转换芯片是pl2303,所以,凡是这种转换芯片做的转换器都可以使用这个驱动,——基于windows32的!方便用于stc单片机的串口下载,这个也是stc官方支持的usb转串口驱动!方便大家共享!-a usefull driver for PL2303,a kind of usb to serial convertor!
PL2303design
- 一款常用的USB接口芯片pl2303的设计资料和编程方法-A common USB interface chip pl2303 design data and programming methods
pl2303-usbser
- 移植的wince6.0中的Public下的USB转串口的代码,目前能用于2303的串口芯片。-Transplantation wince6.0 the Public under the USB to serial port of the code, the current can be used for 2303' s serial port chip.
usbserial
- 常见的usb转串口驱动安装程序,FT232 CH340 PL2303,均经过本人测试-Common usb to serial port driver installation process, FT232 CH340 PL2303, all after I test! !
driver_for_USB_to_serial_port
- 通用USB转串口驱动,用于串口下载程序(而现在很多主机和笔记本都没串口),这是需用到,PL2303-Universal USB-serial driver for the serial download (and now a lot of hosts and laptop no serial port), which is need to rely on, PL2303
prolific
- driver PL2303 You can develope this file
PDIUSBD12
- 官方的PDIUSBD12资料翻译而来,飞本人翻译,资料仅供参考-PDIUSBD12 information from the official translation, I fly translation of data for reference only
pl2303pcb
- pl2303usb转串口,刷机线。包涵pdf图,原理图,和pcb版图。本人开板试用过-pl2303usb to serial port, brush machine line. Bear with pdf maps, schematics, and pcb layout. I tried to open board
sch_pl2303X-transceiver_v1.4
- PL2303 design,including sch,pcb,etc
51_ISP
- 自制51单片机烧录器,USB接口,采用通用型主控芯片PL2303-Made 51 single burner, USB interface, using general-purpose controller chips, PL2303
PL2303
- usb to 232,做USB开发的同志一定要看!-usb to 232, doing USB development comrades have to look at!
PL2303
- PL2303中文资料中文单片机说明书,非常详细,有一定的价值,全中文适合初学者-PL2303 Chinese Data Chinese MCU instructions, very detailed, have a certain value, the whole Chinese for beginners
PL2303
- 带光耦隔离的PL2303串口下载器,注意事项: 1.图中R10到R13不能太大,否则光耦不能工作; 2.如果VCC1电压小于5V,请减小R10和R12; 3.由于本图中的光耦PC817质量不好,波特率不能太高,但能在9600时正常运行,(另外波特率高低貌似与D2、3 、4、5的质量也有关)。-PL2303 serial download device with optocoupler isolation
STC12C5A60S2 PL2303 KD014QQTBN001 W25R128FV
- 用全国产芯片自己“连线”写“汇编”做了个小系统加驱动。芯片:STC12C5A60S2 烧写:PL2303 显示:KD014QQTBN001 闪存:W25Q128FV。细节参见论坛:http://bbs.csdn.net/topics/392176853(A system uses only Hard wire and Assembly, organizes with all Chinese electronic products and their drivers: Chip: STC12C5A
PL2303驱动
- pl2302驱动1.用USB线连接学习板和电脑。随后会听到叮咚一声。并弹出一个对话框。 2.关闭该对话框。运行光盘中PL2303文件夹下 HL2303。按提示进行操作即可 3.安装成功后会在设备管理器 COM口选项中看到连接的COM口是多少 4.打开STC_ISP软件 选择芯片型号,COM口 5.切记 点击下载后冷启动下学习板。即关闭电源,在重新打开下(1. use the USB line to connect the learning board and the computer.