搜索资源列表
S3C2410_BIOS
- 第一版YL2410开发板的BIOS 功能比较简单，上电之后，LCD显示蓝色、绿色、红色三个竖条 同时串口显示如下： Power on reset ************************************ * * * YL2410 Board BIOS V2006 * * Http://www.ucdragon.com * * * ************************************ NAND Flash Bo
S3C2410_BIOS_V2
- NAND Flash Boot Please select function : 0 : USB download file（通过USB下载文件） 1 : Uart download file（通过串口下载文件） 2 : Write Nand flash with download file（将下载的文件烧写到NandFlash） 3 : Load Pragram from Nand flash and run（从NandFlash装载文件并运行） 4 : Era
USB
- LPC2478芯片U盘操作源码，ZLG提供的代码必须用UCOS，NXP提供的DEMO只能操作FAT16系统的U盘，此源码不用系统，并且可操作FAT32文件系统的U盘。此文件缺少ARM7必须的启动代码，分散装载文件等，这部分需要大家自己根据硬件环境编写-LPC2478 chip, U disk Operation Source, ZLG provided code must UCOS, NXP provide the DEMO only FAT16 system, U-disk operation
430USB
- MSP430单片机读写USB程序，非常好！-The MSP430 MCU read and write USB procedures, very good!
USB_drive
- 该代码是基于S3C2410处理器上USB的驱动程序代码，对写USB驱动有很*价值或直接移植即可！-The S3C2410 processor is based on the code on the USB driver code, to write USB driver or there is a great reference value can be directly transplanted!
usb_firmware_example
- 端点批量传输 eerom的读写 固件自动下载 USB标准请求 GPIF单字节读写 GPIF_FIFO读写 Led显示与键盘扫描等-Bulk transfer endpoint eerom automatically download the firmware to read and write USB standard GPIF single-byte read and write requests to read and write GPIF_FIFO scan Led display a
GPIF_fifo
- 实现了ez—usb的GPIF_FOFO读写功能-Ez-usb implementation of read and write functions of GPIF_FOFO
GPIF_Single
- 实现了ez-usb fx2的GPIF单字节读写功能-The implementation of the ez-usb fx2 single-byte read and write functions GPIF
writeUSBdiver
- 10分钟写USB驱动程序 10分钟写USB驱动程序-For 10 minutes to write USB driver for 10 minutes to write USB driver for
arm
- 基于arm的USB读写，通过arm进行对计算机的USB进行读和写的指令-USB read and write using arm
gopen
- 多通道光功率采样，用单片机来控制光开关，并通过USB口来读写-Multi-channel optical power samples, using single chip to control the optical switch, and through the USB port to read and write
udisk
- usb协议应用，arm7，在LPC1768实现u盘读写-usb protocol application, arm7, u disk read and write to achieve the LPC1768
LT-ARM214XPUpan
- 基于arm的u盘实验，优盘虚拟读写实验的源代码-Based on experimental arm of the u disk, USB virtual experiments the source code to read and write
STM32-USB_SD
- STM32 USB简易读卡器C程序，用于STM32单片机用USB口读写SD卡C程序，已调试通过。-Simple C program STM32 USB card reader, USB port for STM32 MCU to read and write SD card with the C program, has been through debugging.
LPC1768-usb
- LPC1768读写U盘FAT16文件的例程-LPC1768 U disk read and write FAT16 file routines
a-USB
- msp430f149单片机USB读写实验程序，本程序已经测试通过-msp430f149 MCU with USB read and write experimental procedure, this procedure has been tested
usb-device-massstorage-project-at91sam7x-ek-iar.z
- When an EK running this program connected to a host (PC for example), with USB cable, the EK appears as a USB Disk for the host. Then the host can format/read/write on the disk. If there is SDRAM on the EK, the disk can be up to 10M so that read/wr
STM32-USB-Host
- 实现了STM32处理器USB host功能，可以读写简单文件-STM32 processor host USB function, you can read and write a simple file
W25Q64 USB
- 通过USB从机接口读写W25Q64模拟一个可移动存储磁盘(Read and write W25Q64 from the computer interface through USB, simulate a removable storage disk)
lpc214x——USB
- LPC214X 系列USB的驱动编写文档说明(LPC214X series of USB drives write documentation instructions)