搜索资源列表
kg
- 本程序是基于51开发的源代码！可以控制开关量!非常简洁。-this program is based on the development of 51 source code! Control Switch! Very simple.
pio
- 基于80C51F020的16路开关量两路模拟量控制通用程序，使用两个独立232串口于PC连接-80C51F020 based on the 16-way switch two analog volume control common procedures, the use of two independent 232 serial port on PC Connection
new6
- 串口通讯，加一些简单的开关量控制，里面有一个简单的通讯协议-serial communications, plus some simple volume control switch, which has a simple communication protocol
80C51chekong
- 8051的测控问题分析，有A/D、D/A、开关量接口-8051 Analysis of the telemetry, A / D, D / A, Switch Interface
rs485asm
- 51单片机开发,24路独立运行的开关量传输机器.在工程应用中可节省大量线材,现在的铜墙铁壁可是好贵的呀.-51 MCU Development, Road running 24 independent transmission switching machines. in engineering application can save a lot of material, But now the iron wall of your good ah.
CAN
- 工业开关量检测模块的原代码,带断线检测功能
dzgsm1
- gsm短消息报警程序，与硬件配合，完成开关量输入，短消息通知主人，用于防盗报警系统。
kglcj
- PIC16F874单片机程序,可以用于对8路开关量进行采集
modbus-51-src
- 汇编，C 源码 用STC89C58单片机做的数据采集和控制，12位AD转换使用TLC2543，通讯协议采用MODBUS（RTU），通过拨码开关改变从机地址，支持模拟量或数字量的读写。（4路模拟量输入、6路开关量输出（继电器输出）、8路开关量输入）开发环境:KEIK 7.06 (2006-7-5，C-C++,61KB,17次) -Microcontroller to do with STC89C58 data acquisition and control, use 12-bit AD
WirelessSend
- 运用无线单片机nRF9E5编写的无线接收的程序，实现开关量的无线串口发射通讯-The use of wireless single-chip wireless nRF9E5 prepared to receive the procedure, to achieve switching capacity of wireless serial communications launch
WirelessRecv
- 基于无线单片机nRF9E5的无线接收程序，实现开关量的无线串口通讯。编成环境KEIL-Based on the wireless single-chip wireless receiver nRF9E5 procedures, to achieve switching capacity of wireless serial communications. Into the environment KEIL
11
- 具有8位开关量输入，8位开关量输出(或带有四位数码显示输出)，并具有8路AD输入（ADC0809）,1路DA输出（DCA0832）的单片机控制系统。系统要求对8位开关量输入信号能够进行监控，8位开关量输出对应8位开关量输入(或用数码显示出来)。对于模拟量输入、输出通道（A/D,D/A），要求编制比例K放大器输出-Switch with 8 input, 8 output switches (or with four digital display output), and 8 with AD i
LED9A
- 9路LED报警程序。对应外部开关量信号，进行实时显示各状态。-9 Lu LED alarm program. Corresponds to the amount of the external switch signal showing the state of the real-time.
KI
- 用于电力系统，使用51单片机来采集开关量的程序，开关量分辨率为0.1ms-Used in power systems, the use of 51 MCU to program the amount of collected switches, switch the amount of a resolution of 0.1ms
LEDctrl
- keilc + proteus 并行口设计指示灯实验 要求：掌握80C51单片机输入输出接口使用方法 学会开关量输入输出控制的接口技术及编程方法 实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc
protel
- 看门狗及数据采集、开关量输入输出、周边电路设计-Watchdog and data acquisition, digital input output, peripheral circuit design
wrong
- 收集8路开关量故障信号，通过RS232送到上位机，并在数码管显示工作状态。-8-way switch to collect fault signal to the host computer via RS232, and the digital display working status.
CollectSys
- 应用FreeScale单片机，基于485网络开发的一个开关量采集系统。-A switch-voltage collection system using FreeScale MCU,based on RS485 communication bus.
biyeshej
- 基于51单片机的开关量检测并通过LCD显示的C语言程序-51 single-chip switch-based detection and LCD display through a C language program
iodev
- IO开关量输入输出(IO switching input and output)