搜索资源列表
msp430x11x1_ta_uart9600_04
- Descr iption: This program demonstrates a half-duplex 9600-baud UART using // Timer_A3 using no XTAL and an external resistor for DCO ROSC. DCO used for // TACLK UART baud generation. The program will wait in LPM4, echoing back // a received ch
f347 uart
- f347 uart tx/rx
RS23(uart)-WiFi
- 串口- 无线局域网wifi模块 Wi-Fi(wlan 无线局域网)作为当今无线领域最为热门的一个技术， 已经应用到各行各业中。它使用TCP标准通讯，技术成熟可靠，传输速率快，各种配套的网络设备十分丰富， 使用者接受程度最高， 全球免费使用，是区域无线通讯的首选方案。 SOC芯片，性价比极高，质量稳定，内置WiFi协议栈和串口传输协议，接口信号5V、地、RX 、TX四线连接； ◆ 模块简洁、体积小，22*60*5 mm； ◆ 用户接口开发简单快捷，串口驱动
AVR
- 16PWM AD KEY LCD LED music light SPI ss usart Uart Tx Rx
uart
- Also the USART automatically senses the start of transmission of RX line and then inputs the whole byte and when it has the byte it informs you(CPU) to read that data from one of its registers. The USART of AVR is very versatile and can be setup
F340_uart
- 本程序是通过F340的uart0与PC进行串口通讯的例程，具体实现为当F340收 *从PC传来的数据后将数据原样回发给PC机 ,端口为RX＝P0.5，TX＝P0.4-This program is through the F340' s uart0 serial communication with PC for a routine, concrete realization of the closing* When the F340 data coming from the PC a
fet140_uart01_19200_2
- MSP430串口0通信，回显收到的字符。波特率19200.-USART0, UART 19200 Echo ISR, XT2 HF XTAL ACLK. Echo a received character, RX ISR used. Normal mode is LPM0,USART0 RX interrupt triggers TX Echo. Though not required, MCLK = XT2.ACLK = n/a, MCLK = SMCLK = UCLK0 = XT2 = 8M
uartdayin
- msp430f5529串口打印程序，实现字符串的发送，用于gsm等。-//****************************************************************************** // MSP430F552x Demo- USCI_A0, 9600 UART, SMCLK, LPM0, Echo with over-sampling // // Descr iption: Echo a received character,
AVRsoftuart2
- 针对amtel avr 部分芯片只有一个串口，在Atmel Atmega 8 上用PB1（TX）PB0（RX）做的软串口程序。-soft uart implementation for atmel avr mcu.
2530_UART_DMA
- CC2530 使用DMA方式 进行串口的收发（IAR 8.30）； 20个字节内，2530将接收的字节进行串口输出。-the tx/rx of uart is used dma
dsPIC33F_ABAUD_V1.0.0
- UART 接收引脚 （ RX 引脚）上的信号能在内部传送至一个输入捕捉模块以获得输入信号边沿的时序。根据该时序，应用程序能正确设置UART 的波特率。-The signal on the UART receive pin (RX pin) can be internally routed to an Input Capture module to time the edges of the incoming signal. From that timing the software can se
e05mle132a
- NRF24LE1 GPIO UART 发送 接收 等例程-NRF24LE1 GPIO UART RX TX ....SOURCE CODE
new_simulation
- 通过时钟使普通的IO口模拟UART串口通讯(Use Timer_A CCR1 hardware output modes and CCR0 SCCI data latch // to implement UART function @ 2400 baud. Software does not directly read and // write to RX and TX pins, instead proper use of output modes and SCCI data // la