搜索资源列表
mdt31
- 这是一个C51做的GPS终端 CPU:89S52 语言: Keil C51 主要是RS232通信-This a C51 done GPS terminal CPU : 89S52 Language : Keil C51 is RS232 communication
vbsourse
- 主从报警系统,单片机编程,是电子课程设计做的东西-master alarm system, microcontroller programming, electronic design courses do things
SPI接口AD转换器代码
- SPI接口AD转换器代码 本代码实现了对串行(SPI)接口的软件模拟 这是在一个项目中要用到SPI接口的器件,调试成功,可以在WAVE下编译通过,可以直接调用 SPI接口AD转换器代码 2002/3/9 design by elven-SPI AD converter code of the source implementation of the serial (SPI) interface software simulation This is a project that will be
PS2与单片机
- 本软件程序为KEILc51开发环境,实现AT89S52单片机与PS2键盘的通讯,同时用液晶LM3037实现同步显示-the software development environment for KEILc51 achieve AT89S52 SCM and PS2 keyboard communications, LCD display synchronized LM3037
毫无保留uCos+Lwip稳定版2
- 网络服务器上实现操作系统和嵌入式协议栈的 结合,对于嵌入式的开发具有实际意义-network server operating systems and embedded protocol stack, the combination of development for embedded real meaning
Wl009LCD 演示程序
- 此程序为单片机开发中的lcd 液晶演示 程序,采用汇编语言编写,经过调试运行 无误。-procedure for the development of SCM LCD LCD demo program using compiled languages, through commissioning and truthful.
矩阵键盘键值lcd显示演示程序
- 此程序为单片机开发过程中的按键扫描程序。采用汇编 语言编写,经调试通过。-procedure for microcontroller development process button scanning procedures. Using language compilation, debugging through.
led小程序
- 此程序为单片机开发过程常用的led小灯闪烁的小程序。用asm编写,供参考。-procedure for microcontroller development process commonly used by small lights flashing led the small program. With asm prepared for reference.
DS18B20-温度控制-LCD
- 此程序为 单片机开发过程中,1—wire总线方式数字温度传感器的控制显示程序。供参考-procedure for microcontroller development process, 1-wire bus mode digital temperature sensor control display program. For reference
串口通讯演示程序
- 此程序为单片机开发过程中的串口通信演示程序。用 汇编编写,供参考。-procedure for microcontroller development process of serial communications demonstration program. Using a compilation prepared for reference.
电磁炉控制
- 压缩文件包括电磁炉的控制程序和其原理电路图!方便大家阅读程序,配合原理图阅读!-compressed files including Induction Cooker control procedures and its tenets circuit! To facilitate reading the procedure to incorporate the diagram read!
7301code
- 一个多媒体液晶显示器内部控制器(主芯片为:7301)的源程序(KC51-an internal multimedia LCD Controller (Controller chip : 7301) of the source (KC51
51单片机系统中运用电脑上的大键盘
- 51单片机系统中运用电脑上的大键盘! Keyboard接线 PS/2--------51 1 DATA------P3.4 3 GND 4 VCC 5 CLK-------P3.3 接在51的外部中断,触发方式为低电平 AT89x51使用12M Modified by Shen Peng! Postgraduate of 2003, 7 Department Harbin Engineering University-51 microcomputer system on the use of t
BC7281A中断方式代码
- 可驱动8/16位数码管显示或64/128只独立LED 的芯片BC72811A中断编程。BC7281A只占用单片机3个I/O口-can drive 8 / 16 Digital Display or 64/128 only independent LED chip BC72811A interrupted programming. BC7281A only occupies three microcontroller I / O port
SERIAL_80C552.
- 飞利浦的80C552串口通信代码,可通过PC机完成对单片机的控制,并向上位机返回数据。-80C552 bunches of communication code of Philip, can finish the control on one-chip computer through the PC , and return to the data in the upward location machine.
PDIUSBD12固件源码
- 修改后的PDIUSBD12完整固件源码,实现51单片机的USB接口,完全通过测试。-revised PDIUSBD12 integrity of the firmware source code, achieving 51 SCM's USB port and fully tested.
drv_nandflash
- drive for nandflash on sansung corp.
E_I
- 这是一个基于MCU的电机控制系统,单片机接收PC的信息,根据Modbus通信协议转换为相应电机控制命令。 整个程序在keil环境下开发,实现了电机的启动、停止、增速、减速、反馈运行时间和速度的功能。-This an MCU-based motor control system, the 8031 PC receiving the information, according to Modbus communication protocol conversion to the correspon
tcp_ip协议栈的ucos代码
- tcp_ip协议栈的ucos代码,主要用于嵌入式系统开发,已经移植到51系统单片机中,通过keil可进行编译,ucos经过最简化改造!特别推荐-tcp_ip CENTER protocol stack code, mainly for embedded system development, has been ported to 51 SCM system, through c51 can be compiled after the most simplified CENTER transfor
大容量串行false45DB081 c51读写源程序
- 串行大容量存储器的c51 读写源程序特点:占用io口线少,缺点:读写时间比并行时间长-Serial large memory read and write the source decoder features : io occupied mouth lines, shortcomings : reading and writing than parallel long time