搜索资源列表
直流、步进电机变成
- 用DSP平台开发的直流电机、步进电机控制的源码程序，已经通过调试。
step.rar
- 步进电机按照细分控制所采用的程序代码设计，可实现精确步距控制,Stepper motor used in accordance with the fine control of the program code designed to achieve precise control of step
Main
- 51单片机控制步进电机,能够控制两个步进电机的步进数和速度-51 single chip contril stepmotor
步进电机转速数码管显示
- 步进电机转速数码管显示，采用C51单片机控制-Stepper motor speed digital display, with C51 MCU
Step_motor
- DSP 2812 的步进电机控制程序 步进电机/延时不能太长，否则转得太慢 /延时也不能太短，否则频率太高不起转-DSP 2812 stepper motor control program stepper motor/delay can not be too long, or turn too slowly/delay can not be too short, or too high frequencies can not afford to turn
STEP_MOT
- 基于TMS320LF2407A开发板的步进电机控制-TMS320LF2407A development board based on the stepper motor control
stepmotor
- 本程序是在CCS环境下利用C语言编写的一个控制步进电机的程序,其中包括控制电机的旋转速度、方向以及步数,从大体上概括了TMS320VC5402的片外围设备及I/O口的编程方式.-This procedure is in the CCS environment using C language under a stepper motor control program, including the control of motor rotation speed, direction, as wel
dsp-stepcontrol
- 一个DSP控制步进电机的程序，含控制部分原理图-A DSP controlled stepper motor procedures, including control over portions of the schematic
EX16_Step
- TMS320F2812控制步进电机的小程序，是我买的电路板QQ2812上的程序，经本人调试，完全可用。但是直接只能驱动很小的电机，大电机要有驱动器-TMS320F2812 control the stepper motor a small program that I bought a program on the circuit board QQ2812, after I debug, fully available. However, can only be driven directly
StepMOT
- DSP 步进电机控制 使用DSP28为处理器，应用更方便-dsp step motor
dsp2812Motor
- 这是一个dsp2812的关于步进电机控制的源程序-This is a dsp2812 on stepping motor control source
dspprogram
- 基于CCS开发环境的，DSP驱动的，运行稳定的带显示的实时控制的步进电机-CCS-based development environment, DSP-driven, stable operation with a display of real-time control of the stepper motor
TMS320F2812_based_SVPWM_division_drive_step_motor.
- 基于TMS320F2812的步进电机SVPWM细分驱动:一个期刊论文，：利用数字信号处理器TMS320F2812的外设事件管理器实现硬件空间矢量脉宽调制(SVP—WM)算法，并结合细分驱动技术，实现了对三相步进电机的驱动及起停、调速等功能的控制。-Stepper motor based on TMS320F2812 SVPWM division drive: a journal article,: Using digital signal processor TMS320F2812 event
bujindianji
- 简单介绍步进电机的控制程序，通过按键来控制电梯的转动。-Simple stepper motor control program introduced by the rotation buttons to control the elevator.
bujindianji
- 用红外线控制步进电机，实现正反转，功能还需继续完善。-Infrared control of stepper motor, to achieve positive inversion, functional need to continue to improve.
EX15_StepMOT
- DSP 2812 PWM控制 步进电机程序 c语言编程 -DSP 2812 PWM controlled step motor program c language programming
stepmotor
- 基于STM32的步进电机的驱动控制 经过测试成功控制-Based on the STM32 stepper motor drive control has been tested successfully controlled
step_motor
- DSP28015开发的步进电机驱动程序，带细分控制。-DSP28015 development of the stepper motor driver, with fine control.
ctrl-speed
- 上位机pc控制步进电机转速，可以用软硬件实现步进电机的启动和停止，可以采用上位机软件实现对步进电机转速的控制。-PC pc speed stepper motor control, stepper motor software and hardware can be used to start and stop, you can use PC software to control the stepper motor speed.
bujindianji
- 步进电机按键控制前进、后退、加速、减速、实现了可变速控制电机；-Button control stepping motor forward, backward, speed up, slow down, to achieve a variable speed control motor