搜索资源列表
thermdsp
- 数字温度计原代码,使用芯片为DS1820,深入理解DSP的BSP端口做GPIO的应用-digital thermometer source, the use of chip DS1820, in-depth understanding of DSP BSP GPIO ports do Application
FIR123
- 1.利用Matlab进行产生频率为1000Hz和6000Hz的正弦信号,利用FDATOOL设计FIR滤波器(fs=16000Hz),以滤波6000Hz分量,并利用SPTOOL工具对信号滤波进行仿真与验证。 2.从MIC端口(J5)输入频率为1000Hz和6000Hz正弦信号的叠加信号,编写实时FIR滤波程序,选择合适的滤波器参数,滤除6000Hz的频率分量,利用示波器在SPEAKER端口(J6)观察输出波形。分析信号的频谱结构,设计满足要求的数字滤波器,-1. The use of Matl
DMA_burst
- 开发环境为visual dsp++3.0的DSP高速端口测试程序-visual development environment for DSP 3.0 DSP-port testing procedures
dspcode
- EBF533开发板上对各端口输入输出数据进行处理的实用程序,包括硬盘、CMOS、视频、以太网等接口。-EBF533 development of the port board input and output data for the practical procedures, including hard disks, CMOS, video, Ethernet, and other interface.
demo_code_for_S3C44B0X
- 三星44b0的测试程序, C语言代码主要是应用代码,包括: 设置使用指令缓存; 修改系统主时钟为32MHz; IO端口功能、方向设定; 初始化中断; 初始化DMF50081液晶模块; 蜂鸣器测试; 液晶显示测试; LED输出测试; 定时器、PWM测试等; -Samsung 44b0 testing procedures, C language code is the main application code, including : the esta
5416UART
- 基于ti公司54x系列DSP的串口通讯程序,本程序可以实现dsp与PC的实时通讯,本人已经验证过,不过你的板子上要使用16C550串口通信模块,它占用DSP的一个端口,用来实现与PC的通信,程序的开始是对它的内部寄存器进行定义。-Series DSP chip serial communication procedures, The dsp procedures can be achieved with the PC real-time communication, I have tested,
bf53x_spi
- blackfin53x的spi,sport端口应用程序-blackfin53x the spi, sport port application
Video_loopback2
- 基于DM642 两路视频输入采集, 两路图像的采集端口为Vport0的高低8位,并将其中一路输出。-two video input acquisition, 2 Road Image Acquisition Vport0 port for the level of eight, with the way the output.
Lab5-IOPort
- 可以在TI5416DSP上运行的I/O端口操作程序
mcbsp
- DSK5510 Mcbsp端口用作SPI部分的C代码
spi
- 将DSPMcbap端口配置成SPI端口的演示代码
dm642videoport
- DM642 网络视频源代码,VP端口采图,通过网口传输。
dsp2812-ADC
- 一个DSP2812的AD采样程序,通过DSP自带的AD端口进行AD转换
Lab05LED
- 瑞泰公司TMS320VC33的例程,实验五I/O端口的基本操作
McBSP
- 5402 用MCBSP 端口 设置音频输出
led
- dsp2407关于I/O端口操作的汇编源程序,直接打开工程文件即可。
SEEDVPM642HardwareTest
- SEED-VPM642 Hardware Test子目录包含SEED-VPM642模板硬件测试程序,包含所有端口功能测试
T6963LCD
- DSP的T6963液晶测试程序,数据端口8000H,代码端口8001H
spi.rar
- 2812SPI 的标准SpI历程,包括了时钟信号设定,SPI-A的外设端口的配置。采用中断控制方式。,SpI course 2812SPI standards, including a clock signal set, SPI-A port of the peripheral configuration. Interrupt control mode used.
基于33F和24H的端口开漏特性设置
- 基于dsPIC33F和dsPIC24H的端口开漏特性设置(Port opening drain characteristic setting based on 33F and 24H)