搜索资源列表
lab014-dcmotor
- 使用DSP2812，的事件管理器（EVB）产生的PWM波，输出在PWM11引脚，去控制直流电机速度。-use DSP2812, the event management (EVB), the PWM wave output pin in PWM11 to DC motor speed control.
SensorlessBLDCDriveControlAssemblyCode
- 该软件是关于无刷直流电动机调速控制的汇编程序，对应的DSP处理器是TMS320F24xx,解压后会出现CCS开发环境下的整个工程。-on brushless DC motor speed control the compilation process, the corresponding DSP processor is TMS320F24xx. extracting CCS will happen after the development environment of the whole p
BLDCwithsensorlesscontrolprogramme240
- 该软件是关于无刷直流电动机无传感器调速控制的汇编程序，对应的DSP处理器是TMS320F240,解压后会出现CCS开发环境下的整个工程。-on brushless DC motor speed control sensor compilation procedures, the corresponding DSP processor is TMS320F240. extracting CCS will happen after the development environment of the
直流电动机单级性双闭环可逆控制程序
- 用DSP实现直流电动机速度，全部控制程序包括速度PI调节，电流PI调节，PWM控制，主程序进行电机转向的判别-DSP DC motor speed control procedures including full speed PI regulator and current PI regulator, PWM control, the main program for the motor to discriminant
直流电机的速度环PI控制-速度电流检测部分的程序
- 直流电机的速度环PI控制-速度电流检测部分的程序，各部分都已经有了-DC motor speed loop PI control- speed current detection part of the program, all parts have been ~ ~
motor-PI
- 主要设计了直流电机的速度环PI控制，包括DSM图和C程序-The main design of the DC motor speed loop PI control, including DSM program plans, and C
motor
- 这是一个控制无刷直流电机调速的程序，采用c语言编程，适用于tms320f2812-This is a brushless DC motor speed control procedures, using c language programming for TMS320F2812
DSP_relative_code
- TMS320LF2407 相关代码：RS232通信程序，无刷直流电动机调速程序，直流电动机单极性可逆双闭环PWM控制程序等-TMS320LF2407 relevant code: RS232 communication program, brushless DC motor speed control program, reversible double-loop DC motor unipolar PWM control programs
zhiliudianji
- 直流电动机闭环系统调速数字控制系统的设计 -DC motor speed closed-loop system the design of digital control system
zhiliudianjishuzikongzhixitong
- 直流电机闭环调速数字控制系统设计,采用八位开关SKAIGUANG1000的8个拨动开关(K1-K7)控制直流电机的速度等级SCI发送数据控制电机正反转，发送00表示正转，发送01表示反转,当速度超过500r/min时，DSP向上位机发送速度值-Closed-loop DC motor speed digital control system design, using eight switches SKAIGUANG1000 of 8 toggle switch (K1-K7) control
DSP2812-Motor
- 利用DSP的PWM1和PWM2,然后经过了两级放大控制直流电机，若要改变电机转速或转向,可在DSP28_EV.c文件里按相应注释修改，即实现PWM波来控制电机。-Using DSP-PWM1 and PWM2, and then amplified through a two DC motor control, to change the motor speed, or steering, can DSP28_EV.c file comments by corresponding changes
Three-phase-brushless-DC-motor
- 三相无刷直流电机的控制程序，里面详细的介绍了控制电机转速，控制电机正反转的程序-Three-phase brushless DC motor control program, which detail the control of motor speed, reversing motor control program
stepping-motor
- 直流步进电机键盘控制LCD显示菜单，+为开始进入，4为切换 ，7为进入子菜单，stepping motor 为步进电机，2控制转速，0控制节拍，MOtor v3000为直流电机，8正转，7反转PWM控制-DC stepper motor keyboard LCD display menu,+ is entered, 4 switching, 7 to enter the sub-menu, stepping motor as a stepper motor, 2 speed control, 0
motor
- 直流电机调速控制 直流电机调速控制 直流电机调速控制-DC motor speed control DC motor speed control DC motor speed control
DC-MOTOR
- 直流电机调速为自身学习过程中总结的一些基本的通信规范和协议，和大家共享。-DC motor speed control for their own learning process in a summary of some basic communication standards and protocols, and share.
SCM-brushless-dc-motor-speed-control
- 具有梯形反电动势的永磁同步电动机通常被称为无刷直流电动机，它具有结构简单、体积小、重量轻、效率高、高功率密度、启动扭矩大、惯量小和响应快等其它种类直流电机无法比拟的特性。采用电子换向器替代了传统直流电动机的机械换向装置，从而克服了电刷和换向器所引起的噪声、火花、电磁干扰、寿命短等一系列弊病。-With a trapezoidal back-EMF permanent magnet synchronous motor is often referred to as brushless DC mo
Motor
- 实现对直流无刷电机转速的控制程序，可通过键盘控制启停和转向并得到实时转速-Achieve the brushless DC motor speed control program, start and stop can be controlled through the keyboard and get real-time speed and steering
DC-motor-adjustable-speed
- 利用at89c51实现直流电机可调速控制，可以正转。反转，暂停，加速和减速等-Use at89c51 DC motor speed control, you can forward. Reverse, pause, acceleration and deceleration
Motor-Speed-Set-and-Control
- 利用PID算法实现直流电动机调速，可用16个按键精确设置转速值，并在8279数码管上显示当前转速、电压和设置转速。同时，系统还具有堵转判断功能。当电机在外力作用下被强行停止时，系统可自动停止运行，保护电路。-PID algorithm to achieve the DC motor speed control, 16 keys available to accurately set the speed value, speed, voltage and set the speed on the
DC-motor-speed-control
- 单片机开发板的直流电机调速...对于初学者是一个不错的学习开端-MCU development board of the DC motor speed control