搜索资源列表
sendlcd
- C8051F040中发送显示液晶屏各种子程序例程-C8051F040 LCD screen shows various subroutine routines
红外23112
- 红外接受的发送程序载波３８k，用指令来延时，调试通过-infrared accept this procedure carrier 38k, with orders to delay, debugging through! !
vc123456
- c#开发手机程序,手机接收和发送数居包的程-c# development handset procedure, the handset receive and the transmission number occupy a package of regulation
VC_AD_TEST1
- ad板数据采集程序，用ｖｃ编的程序，用数据信号发生器在ａｄ板接口连接发送信号后可以在窗口得到信号的图形-ad board data acquisition program, vc series of the procedures used in the data signal generator ad plate interface to send signals can get the signal window graphics
HowToUseSpcomm
- 使用spcomm控件进行串口通信的程序，包括数据的发送与接收，同时采用定时发送的方式，delphi语言编写。-spcomm used for serial communication control procedures, including data transmission and reception. Timing also adopted this approach, delphi language.
Series_60_Platform_1st_2nd_Edition_SMS_Example_v1_
- symbian平台，s60操作系统短信发送的源代码-symbian platform, s60 messages sent by the operating system source code
ReadFIFOData
- C8051F040 读FIFO数据并且通过串口发送至PC-C8051F040 read FIFO data sent through the serial port to PC
串口发送modbus协议CRC校验
- 串口发送modbus协议CRC校验低字节（若为查表所得数据为高字节，其实为CRC的低字节）-serial modbus connection agreement low byte CRC (if available for look-up table for the high-byte data, In fact, for low-byte CRC)
DMX512发送程序
- 用ARM实现DMX512数据的发送与接受！ 程序已测试，无错
TM1804 数据发送格式原程序
- 功能：TM1804 数据发送格式 设置：Set up tim 18ms 16M High Crystal COLCK=2 Target power self WATCHDOG=DISABLE RESETENABLE=DISABLE RCOUT=P64 date:2010-08-08
C8051f330_CC1100无线发送
- c8051f330控制无线模块CC1100发送C程序代码
nRF905andC51 无线发送模块Nrf905与c51单片机相连接的接收模块
- 无线发送模块Nrf905与c51单片机相连接的接收模块，程序是用C语言编写的-Wireless transmit module Nrf905 c51 microcontroller connected with the receiver module, the program is written in C language
vc.rar
- 以VC编写的USBCAN通讯的发送和接受界面，可以设置为扩展帧和标准帧等，也可以查看发送和接受到的报文。,VC prepared to USBCAN send and receive communications interface can be set to extend the frame and standard frame, also can check to send and receive the message.
uart
- 51单片机 串口接收发送 都用到中断 全双工 采用C语言-51 MCU serial port receive interrupt is used to send both full-duplex using C language
TFTP
- 通过TFTP协议从网口下载数据。源码中board_eth_rcv()用于接收数据，将该数据上传给ip层。board_eth_send()用于将上传过来的数据包发送出去。-Through the TFTP protocol to download data from the net mouth. Source board_eth_rcv () used to receive data, the data upload to the ip layer. board_eth_send () is us
screenshot_v3[1][1].03_src
- 这是一款 自己写的彩信发送程序 功能不是太完善 请多谅解 it is a code and it is discribe the mmsend-it is a code and it is discribe the mmsend
无线接收发送程序
- 单片机解码和编码程序，利用IO进行接收和发送达到一定的效果
基于STM32 的1527码发送程序
- 基于STM32F103 处理器的EV152发送程序
XS128 _CAN接收和发送
- CAN接收和发送的小程序，可用于简单的调试(CAN receive and send a small program, can be used for simple debugging)
Project_CC1101——发送接收分离
- Project_CC1101——发送接收分离(Project_CC1101 - send and receive separation)