搜索资源列表
embededserial
- 与PC机见进行串口通讯连接 串口通信程序 串口通信程序-see and PC serial communications link for serial communication procedures serial communication program
Vend_ax
- CYPRESS USB CY7C68013A 命令传输的固件和上位机程序-CYPRESS USB CY7C68013A command transmission firmware and PC program
CNC_3Axis
- Source code for PIC microcontroller to control 3 Step motor, communicate with PC via LPT port. Application: CNC machine, 3 axis machine-Source code for PIC microcontroller to control 3 Step motor, communicate with PC via LPT port. Application: CNC ma
serial_comm
- DTR/DSR handshaking is used because this is what the POS printer requires. Comms with a pc can then be accomplished using the same cable as used for the printer. Ensure that the pc program is written to use the same handshaking.
burst
- 是一个PCI上位机程序，用于从PCI数据采集卡中读取数据。-PCI is a PC program for data acquisition from a PCI card to read the data.
cypress-68013
- cypress 上位机程序，USB2.0-cypress PC program USB2.0
PC-Base-Signal-Analyzer
- PC Based Signal Analyzer This aims of the project just familiar to a Digital oscilloscope. It is used for capture the different signal such as SINE WAVE, TRIANGLE WAVE and the SQUARE WAVE. Use the A-to-D converter into a binary form. Thus, the data
xinhuaRFID
- delphi RFID读写器上位机程序，值得参考-the delphi RFID reader PC program, worth considering
Program
- teleferra source code - to control the car by using keypad on PC/Laptop
Program-to-interface-GSM-Module-with-8051-microco
- Program to interface GSM Module with 8051 microcontroller (AT89C51) using PC and LCD-Program to interface GSM Module with 8051 microcontroller (AT89C51) using PC and LCD..
USBLED
- 利用CY7C68013A 控制LED显示程序 上位机程序和固件程序-Using the CY7C68013A control LED display program PC program and firmware
arduino_serial_N_Servo
- arduino 串口控制程序双舵机(可扩展多个舵机含上位机程序)-arduino serial control procedures dual steering gear (can be extended multiple servos with the PC program)
0002
- VB遥控播放器红外遥控解码,含VB遥控音乐播放器上位机程序-VB remote player infrared remote control decoding, including VB remote PC program music player
shangweiji
- vb6.0写的一个步进电机驱动器上位机程序，可生成exe文件。用于单个驱动器的驱动。-Writed by vb6.0，it is a stepper motor driver PC program that can generated to exe file.It is for a single drive.
PID-Temperature-Control
- 这是我的原程序，设计的硬件电路，上位机程序，希望对大家有帮助.温度控制-This is my original program, the hardware circuit design, the PC program, we hope to help. Temperature control
wifirobt
- WIFI智能小车上位机控制程序，可以用net4.5以上打开-WIFi control car PC program
68013
- 68013芯片的驱动程序，固件程序，以及上位机程序源代码-68013 chip drivers, firmware, and PC program source code
GUI
- 单片机uart上位机程序，通过matlab编写，显示波形及16进制转换-Microcontroller uart PC program, prepared by matlab waveform display and hex conversion
VBDS1302proteus
- VB上位机程序控制DS1302时钟的proteus仿真-VB PC program control DS1302 clock proteus simulation
Com_Vb
- 接收串行数据的单片机上位机程序。使用VB编写，解析单片机发送过来的串行数据。 单片机是8052,搭载了TCS3200光学颜色采集器，将采集到的数据通过RS232发送到PC，显示RGB数值，在label控件中显示该RGB数值的颜色。 串口数据格式是RGB24位加一位识别码/-Receive serial data microcontroller PC program. Using VB to write, parse microcontroller serial data sent ove