搜索资源列表
ddr_controller
- 完整的DDR控制器设计,包含代码、仿真环境、FPGA综合网表等-full DDR controller ip,include rtl code,simulation environment and testbench, fpga synthesis netlist,etc.
TC6014
- STM32F103ZET6和专业的电机控制芯片TC6014设计的四轴电机控制器,包含原理图PCB-STM32F103ZET6 and professional motor control chip TC6014 designed four-axis motor controller, including the schematic PCB
cnc
- 共享老外的AVR CNC控制器 共享老外的AVR CNC控制器-Foreigners CNC AVR controller Foreigners CNC AVR controller
rtu
- 低功耗水资源控制器RTU 支持8路0-20mA模拟输入A/D转换功能,主要用于驳接投入式液位计以及其它任何形式的模拟信号的处理-Low-power water controller RTU supports 8-channel 0-20mA analog input A/D conversion function, mainly used for connecting the input level gauge and any other form of analog signal proces
Direct-reading-water-meter
- 脉冲直读水表是内含控制器,通过采集脉冲方式,具有RS485总线远传,抄表数据与表盘显示数据一致的水表。 -Direct reading water meter Pulse direct reading water meter is included controller, through the acquisition of pulse mode, with RS485 bus remote transmission, meter reading data and water table
chenzhongkongzhiqi
- 一款用protel软件开发的称重显示控制器根据图纸可以直接从事生产,非常有用,吐血奉献。-Using a Protel software development of weighing display controller according to the drawings can be directly engaged in the production, very useful, hematemesis dedication.
Elevator_controller_based_on_74
- 基于74系列数字芯片的8层电梯控制器,Multisim13仿真-An 8- layer elevator controller based on 74 series digital circuit chip.
AD9_C51_RS485
- Altium Designer设计的基于51的最小系统,主要包括RS485控制器,温度传感器,51单片机,晶振,复位等功能模块-Altium Designer designed 51-based minimum system, including RS485 control, 51 single-chip, crystal, reset and other functional modules
抱闸控制器
- 抱闸控制器,用PWM方式控制电机抱闸,在有效开通抱闸情况下缓解抱闸发热(The brake controller, using PWM to control the motor brake, brake in effective opening off brake fever)
i2c_ctrl_master1
- I2C总线控制器,master端,控制寄存器读写(I2C Master controller)
SG-MPPT-HL-K-V1
- 原理采用Altium Designer软件设计,内含MPPT的BUCK拓扑结构、DCDC复制电源转换、微控制器等电路(The principle is designed by Altium Designer software, including MPPT BUCK topology, DCDC copy power conversion, micro controller and so on)
SG-GL(WS)-K-V7
- 采用Altium Designer软件设计,与程序一起可以直接出产品!(Using Altium Designer software design, with the program can be directly out of the product!)
T2白光控制器C文件
- 自制电烙铁,stc15发204ea源代码。diy专用。
CMSIS-DAP-V2.0
- DAP-LINK工具STM32源码,支持STM32F103作为控制器(DAP-LINK Tool STM32 Source Code)
地址编码器SCH+PCB
- 地址编码系统主要由一个主控制器和多个从编码器构成,其中主控制器安装在控制室低压柜内,从编码器安装在在拉绳开关或跑偏开关内。它们之间通过直流载波通讯相接,所有从编码器的地址都是唯一的,工作时由主控器逐一发送从编码器的地址,所有从编码器收到地址后同自身所设定的地址相比较,只有地址相同的编码器才会产生应答,将被编码的开关类型及工作状态发给主控器。 CPU核心电路选用STM8S系列8位单片机,型号为STM8S103K3T6C,最高运行速率16MHz。功耗极低,在最高速率下,5V电源供电所需供电电流小于
基于 LED显示屏 的 电子时钟
- 该硬件电路 由 8086系统 、 4 线- 16 线译码器 74154 、 可编程并行 I/O接口芯 片 8255A、 可编程计数器 /定时器 8253A、可编程中断控制器 8259、双 4输入或 非门 4002、六输入反相器 74LS04、 LED显示器、按键开关 、电阻 构成 。电路 LED显示器采用多位数码管动态扫描、分时循环显示原理,用 8255的 PA口和 PB口 分别作为段选和位选。