搜索资源列表
zhoudeqiangdujisuan
- 轴的强度计算公式，包括轴所传递的功率 P轴的工作转速 n轴所传递的扭距 T增大后的轴端直径等内容。-The strength of the shaft is calculated, including the contents of torque T P shaft power delivered operating speed n shaft increases passed after the end of the shaft diameter and the like.
BLDC
- 无刷直流电机的控制仿真，主要PWM三相控制，无转矩脉动-Brushless DC motor control simulation, the main PWM three-phase control, no torque ripple
DTCDPE
- 直接转矩控制无刷直流电机的matlab仿真程序，PI闭环调节-Direct torque control brushless DC motor matlab simulation program, PI closed loop control
DTC_LOW_SPEED
- Simple Flux Regulation for Improving State Estimation at Very Low and Zero Speed of a Speed Sensorless Direct Torque Control of Induction Motor
DTC
- 电力牵引直接转矩控制DTC的介绍文献，内含圆型磁链传统滞环，ISC，以及部分改进型定子磁链模型搭建介绍，比较具有代表性。-Electric Traction Control DTC direct torque introduced documents containing the conventional circular flux hysteresis, ISC, and some improved stator flux model to build reports, compared wi
PMSM_simu_test
- 永磁同步电机(PMSM)电流转速双闭环PI控制，采用矢量控制（FOC）中的id 0方式，以空间矢量脉宽调制来实现磁链圆跟踪。对负载转矩进行交轴电流前馈以抑制外负载扰动。-Permanent Magnet Synchronous Motor (PMSM) current double closed loop speed PI control, vector control (FOC) of id 0 mode, space vector pulse width modulation to ac
3IM-inversion
- 主要包括三相异步电机的反转程序，通过示波器可观察电机反转时转速、转矩情况。记得要改仿真路径！-Including three-phase asynchronous motors reverse procedure can be observed through the oscilloscope reverse motor speed, torque situation. Remember to change the path simulation!
3IM-start
- 三相异步电机的启动程序模型，simulink模型。通过示波器观察启动电流，起动转矩情况。记得要改仿真路径！-Start program model three-phase asynchronous motors, simulink model. Starting current through an oscilloscope, starting torque situation. Remember to change the path simulation!
Tower-crane-moment-limiter
- AVR单片机采集塔机重量、高度、风速、幅度信号，监控塔机工作参数，提高塔机工作安全性的力矩限制器。-AVR Microcontroller collection tower crane weight, height, wind speed, amplitude of the signal, control tower machine operating parameters to improve the safety of tower crane torque limiter.
ninubi
- 基于s-function的DFIG模型，输入dq轴电压、转差、驱动转矩，输出dq轴电流、电机转速-s-function model of DFIG based input dq-axis voltage, slip, drive torque, output current dq-axis motor speed
wind
- PSCAD做的风力机模型，嵌入了3维风力特性曲线，动态调节转矩与转速。-PSCAD do wind turbine model, embedded in the 3 d wind characteristic curve, dynamic torque and rotational speed adjustment.
PMSM_DTC_traditional
- 这是一个关于永磁同步电机直接转矩控制的MATLAB仿真模型，使用传统的直接转矩控制-This is a permanent magnet synchronous motor direct torque control of MATLAB simulation model, using the traditional direct torque control
PMSM_DTC_improved
- 这是一个三相永磁同步电机基于滑膜控制的直接转矩控制。-This is a three-phase permanent magnet synchronous motor direct torque control based on synovial control.
EV_dynamic_model01
- 汽车动力学simulink模型，用于将速度信号转化为扭矩信号。-vehicle dynamic model, used for converting the velocity signal to torque signal
ylbjq
- 发动机净外特性曲线；发动机与变矩器共同输出特性；发动机净外特性曲线；液力变矩器原始特性曲线；变矩比与变矩器传递效率；液力变矩器泵轮转矩系数；发动机与变矩器共同输入特性(The net engine characteristic curve of engine and torque converter; output characteristics; engine net characteristic curve; hydraulic torque converter original chara
Battery_model
- 建立了一个基于等效电路的电池模型，输入为电机1和电机2的扭矩和转速，输出为电池电荷量SOC，能够广泛应用于混合动力汽车整车模型的搭建和验证。(Set up a model based on equivalent circuit of the battery, the inputs are the torque and rotational speed of motor 1 and 2, and the output are the battery SOC, it can be widely us
伺服电机扭矩计算
- 伺服电机扭矩计算方法，伺服选用、伺服使用、故障排除。(Servo motor torque calculation)
Linkage Calculation Notebook for M2
- matlab notebook to calculate torque and optimize link design.
DY1
- MATLAB模型，是永磁同步发电机根据转矩不同发出的不同功率，通过仿真，可以方便的分析，永磁同步发电机输出功率。(MATLAB model is the power of permanent magnet synchronous generator according to different torque. Through simulation, it is convenient to analyze the output power of permanent magnet synchrono
MATLAP
- 汽车转向时的转向力矩与转角的关系，转向力矩与车速的关系(The relationship between steering torque and rotation angle in automobile steering)