搜索资源列表
a628tva
- 奥迪A6 2.4T ecu 件号为：mpfi-V6 的ecu改装目标代码。改装目标：加速提高1.2秒左右 最高扭矩出现降低到2475转。 下次再上价值8万元的德国房车赛中使用ecu p/n: M.1.5.4 ecu 改装程序文件。-Audi A6 2.4T ecu Parts : mpfi-V6 ecu modified object code. Modified goals : enhancing about 1.2 seconds maximum torque to be lower
Lsqcurvefit-Torque
- Lsqcurvefit-Torque，最小二乘法曲线拟合，主要用于发动机负荷曲线的拟合工作。
niuju.ZIP
- 电机转速、转矩微机测试的样例程序。供工程人员参考。-Motor speed, torque computer sample test procedures. Reference for engineers.
MotorTestbenchV3
- Tests Electric Motor for Speed, power, Brush wear & Output Torque Verion 03-Tests Electric Motor for Speed, power, Brush wear & Output Torque Verion 03
feijijiyiwanjianniujisuan
- 题目所给飞机机翼受的是平均载荷，所以要计算每一站点上的剪力，弯矩和扭矩，就要先算出其所在平面的面积和其合力作用线到某一座标轴的距离，及集中载荷作用线到中心线的距离。带载荷等于面积乘以平均载荷，某一站点剪力等于此站点之前所有带载荷之和。弯矩等于剪力乘以合力作用线到其对应坐标轴的距离。扭矩等于剪力乘以集中载荷作用线到中心线的距离。所得结果与笔算结果基本吻合。程序具有一定的通用性。-Subject to the aircraft wing by the average load is, so each
thesis
- 2009nuaa南京航空航天大学毕业论文。《DTC直接转矩控制的实现》.内含simulink模型。可在matlab7.0以上直接运行。PS: 此模型为建立在数学模型基础之上，未使用power sysytem toolbox。（因toolbox版本不同会产生不兼容现象）-Thesis of Nanjing University of Aeronautics and Astronautics 2009 nuaa. “DTC direct torque control to achieve.” Sim
idealmodel
- 对采集的感应电机三相电压电流进行处理，计算电机的转矩和转速。-Calculate the motor s torque and speed base on v and I
svpwmdtc
- SVPWM驱动的直接转矩控制仿真模型。 svpwmdtc.rar-SVPWM drive direct torque control simulation model. svpwmdtc.rar
pmsmdtc
- simulink永磁同步电机直接转矩控制系统仿真-simulink Permanent Magnet Synchronous Motor Direct Torque Control System Simulation
A-comparison-of-stator-flux-linkage-estimators-fo
- A comparison of stator flux linkage estimators for a direct torque controlled PMSM drive
torque
- 模拟浮子式波浪发电系统输出机械转矩的模型-Analog float wave power system model output mechanical torque
torque_motor
- Torque motor induced back-emf calculation (Matlab with user-friendly GUI)
Match-of-engine-and-torque-converter
- 发动机与液力变矩器的匹配设计与计算,适合装载机与推土机-Match the design and calculation of the engine and the torque converter, suitable for loaders and bulldozers
Motor-control
- 发动机matlab模型，可以实现发动机外特性曲线，发动机控制，包括油门开度，转速，转矩等参数-Matlab engine model can be achieved outside the engine characteristic curve, the engine control, including the throttle opening, speed, torque and other parameters
direct_torque_control
- 感应电机的直接转矩控制，控制目标位感应电机，方式为直接转矩控制。-Induction motor direct torque control of induction motor control target, by way of direct torque control.
svxw
- 本程序是基于matlab的永磁电机的直接转矩控制系统-This procedure is based on matlab permanent magnet motor direct torque control system
zjzjtest
- 直接转矩控制技术.doc 例1、CLARK变换的DSP实现 例2、PARK变换的DSP实现 例3、空间矢量的算法程序 -Direct Torque Control technology. Doc Cases 1, CLARK Transform DSP realization of cases 2, PARK Transform DSP realization of Example 3, the space vector algorithm
DDVC
- 本程序主要是关于带转矩内环控制的交流异步电动机矢量控制的建模与仿真-This procedure is mainly about the inner control with torque AC induction motor vector control Modeling and Simulation
direct-torque-control
- 异步电动机的直接转矩控制Matlab/simulink仿真模型-Asynchronous motor direct torque control Matlab/simulink simulation model
Torque-Liniter
- 力矩限制器，采集重量及角度，测算幅度，根据性能表算出额定载重，计算参数输出控制。-Torque limiter, gathering weight and angle, estimated magnitude of rated load is calculated according to the performance table, calculating the output parameter control.