搜索资源列表
daolibai
- 一个用MATLAB/SIMULINK做的四级倒立摆的控制系统模型-a MATLAB / Simulink do four inverted pendulum control system model
pend
- 这是一个通过vc实现倒立摆的小程序,但效果并不是太好,希望有人能改进它,我的ez-mail是wzq204@163.com-This is a realization by vc inverted pendulum of small programs, but the results are not good enough, that it was to improve it, the ez-mail is wzq204@163.com
ipen_lqr_pid
- 单级倒立摆建模_先进PID控制MATLAF仿真-single-inverted pendulum modeling _ advanced PID control MATLAF Simulation
InvertedTry
- 基于一级倒立摆实物控制代码,整个程序还没有在实物测试,希望高手给指点一下。-based on an inverted pendulum control code in kind, the whole process has not been tested in the physical, hoping to master this kind.
neuralnetwork-daolibai
- 倒立摆matlab程序设计与实现 倒立摆matlab程序设计与实现-inverted pendulum Matlab Program Design and Implementation of an inverted pendulum Matlab Program Design and Implementation
L1InvertedPendulum_chy
- 一阶直线倒立摆的受力分析,应用lagrange方法,用mathmatica编制。-a band linear inverted pendulum Analysis, Application ESO, mathmatica compiled with.
pendulum
- 自己编制的倒立摆matlab7的程序,采用神经网络控制方法
DaoLiBai
- 倒立摆仿真程序,可设置摆的摆角,角速度,速度
一级倒立摆
- 模糊控制 倒立摆 空间状态
inverted-pendulum-LQR-controll 单级倒立摆的LQR控制器的设计
- 其中包含和倒立摆的论文以及自己编的matlab文件-Single-stage inverted pendulum LQR controller design which contains the inverted pendulum and paper files as well as their own series of matlab
pundulum
- 对于单级倒立摆的仿真以及控制的原理图以及源代码-The Inverted Pendulum Simulation and control schematics and source code
pend
- 一阶倒立摆建模,仿真效果的程序,同时还进行了极点配置!-Inverted pendulum modeling, simulation results of the procedure, but also for the pole assignment!
PID
- 利用Matlab的GUI界面来进行倒立摆PID参数的设计-The design of PID parameter control of inverted pendulum using Matlab GUI
fuzzyPID
- 基于LABVIEW的倒立摆模糊PID控制程序,界面美观,运行效果非常好!-LABVIEW-based inverted pendulum fuzzy PID control procedures, beautiful interface, runs very good!
fuzzycontrol_daolibai
- 使用labview编写的基于模糊控制的小车倒立摆程序-Using labview prepared based on inverted pendulum fuzzy control car program
daolibai
- labview倒立摆上位机程序,是2013年9月分全国电子设计大赛的作品,但是可惜的是,电子大赛不能用电脑,很遗憾,发上来让大家参考,写的不好,希望多包涵-labview handstand put crew procedures, 2013 September, 2011 National Design Competition works, but unfortunately, can not use a computer electronic contest, unfortunately,
Labviewpendulm
- Labview制作的倒立摆仿真试验,大家可以参考一下-Labview produced inverted pendulum simulation, we can refer to
daolibai
- 倒立摆用编码器支撑,51单片机控制,只是基础功能-Pendulum encoder support, 51 MCU control, only basic functions
pid
- 比例 积分 微分 头文件 闭环控制 调节倒立摆-Proportional Integral Derivative
chegnxu
- 台式车倒立摆模型的滑模控制的MATLAB仿真程序,包含滑模控制器代码与台式车倒立摆模型(Sliding mode control of inverted pendulum model of table car,the code of sliding mode controller and the inverted pendulum model of desktop vehicle.)