搜索资源列表
xpm3
- 该文件的内容是设计一个五层楼的电梯控制装置,要求每层楼根据需要控制设上下控制按键及按键指示灯,全部楼层只设置一个当前楼层显示 电梯内设开关门按键 各楼层按键及指示灯,开关门要有声响提示 每层楼高度为0.30米,楼层全高1.5米-the contents of this document is to design a five-storey building in the lift control device on each floor under the requirements necess
MABIAO
- 开发了,带四位显示的秒表, 按键启动停止,用定时器按键去抖-development, with four shows in the stopwatch button activated stop using the timer button Tremble
20063161712468
- 序(约延时8ms)后再回到按键查询状态,不断循环;有按键时,LED动态显示子程序作为按键防抖延时被连续调用二次(约延时16ms),待按键处理程序执行完后,再回到按键查询状态,同时兼顾了按键扫描取值的准确性和LED动态显示的稳定性。秒定时采用定时器T0中断方式进行,60秒计数由定时-sequence (about 8ms delay) to come back button inquiries and continuously cycle; When a button, LED dynamic d
clock
- 这是个显示钟表的小程序 通过汇编在DOS下显示和系统一样的时间 并能通过按键来改变颜色,大小等-This is a small show clocks in the process by compiling DOS system and displayed the same time and pass keys to change the color, size, etc.
anjianzlg7289
- 此为用51单片机控制zlg7289芯片的按键和LED显示程序。-to use this 51 zlg7289 chip microcontroller control buttons and LED display program.
KEYWYSET
- 4*4带位移显示的按键实验-4 * 4 with displacement experiments showed that the keys
8051changsheng6zhongboxing
- 8051产生6种频率可调的波形发生器。由10个按键控制。每换一次频率或波形都要等1602显示完后才会产生波形-8051 produced six adjustable frequency waveform generator. From 10 control buttons. One for each frequency or wave will have to show that after 1602 would have Waveform
asm_music
- 程序说明: 1. 程序实现了三个音乐程序的演奏,同时画出音乐波形. 2. 演奏程序,输入键盘上对应的键,(按键对应的波形值可以在程序中修改)可以演奏出音乐并显示出对应的波形.-procedures : 1. Realization of the three procedures music performances, Meanwhile painted music waveform. 2. perform procedures, keyboard input correspondin
p16demo
- PIC16代码示例包含IIC程序,AD采样,液晶显示\\按键处理-PIC16 code example contains IIC procedures, AD, LCD \\ handling keys
ND22
- 一款功能比较复杂的家电控制器程序,采用S3F9454,含遥控,按键,显示等全部程序-one of the more complex functions of home appliances controller procedures adopted Chip, with the remote control, keypad, display all the procedures
pinlvjichange
- 测量频率范围:0~5KHZ,测量结果由LED显示; 基本频率上限3KHZ,下限10HZ,超出范围点亮L9报警; 上、下限可通过按键调整。 -measurement frequency range : 0 ~ 5KHZ, the measurement results from the LED display; 3KHZ fundamental frequency cap, minimum 10 9999, outside the scope of lights to install
yxcvcxvcxbvcx
- (红外线遥控)将万能遥控按键的键值通过At89s51P1口的8个LED显示出来-(infrared remote control) Universal remote control keypad keys through the At89s51P1 I was eight LED said out
PIC_STUDY
- 完整的PIC学习程序示例 软件功能: RT1602C驱动 UART串口输出,波特率为19200 按键扫描: 键1控制LCD的显示状态,接收状态或是发送状态 键2循环控制UART将要输出的子串口 AD转换功能 UART串口接收中断 TIME1定时器中断 具体请参考硬件连接图-integrity of the learning process software examples : RT1602C driven serial UART output. ba
kelan
- 按键1通过液晶显示从18b20读取的当前温度-through a button LCD 18b20 read from the current temperature
anjianjishuqi
- 知识要点:理解熟悉散转结构的程序 运行结果:按P3.2 或3.3(低4 位的任意一个键盘)第一位数码管加1 直到9 循环 开始显示0把P3 送OFH,判断有没有按键,没有则反复循环,有按R0 加1,如到10 那么则清除, 最后根据R0 的值散转.-knowledge points : understanding the structure familiar to the casual result of running the program : by P3.2 or 3.3
shuzinaozhong
- 具有按键控制,时间可调,可设定闹钟时间,LED显示-with button control, adjustable time, set alarm clocks, LED Display
yinyuebofang
- 一、 使用键盘显示接口芯片8279接收按键键值,并在七段数码管上显示出来,通过判断键值进入相应音乐播放处理程序。在音乐播放程序中,使用定时器/计数器8253的计数器2,使其工作在方式¬ ¬ 3—方波发生器,通过查表依次取出乐曲频率值送入计数器作为计数初值,经out2输出方波,驱动扬声器发出不同频率的声音,在每个音阶之间加入相应的延迟时间,即实现了音乐的播放。
time
- 工作环境为: 按键采用中断方式 IIC总线接通 P0口上拉 LS244使能 接通数码管 K0:确定键,用来确定调节好的时钟或者闹钟 K1:时钟调节键,用来选择时钟调节的位置 K2:调节键,用来使选中的数字发生改变 K3:闹钟调节键,用来选择闹钟调节的位置 接通电源后可能需要按一次K4(复位键),时钟才会开始走动,此时是一个默认的时间,使用K1来选择需要更改的数字的位置,然后按K2调节,所有的数字都调节好后按K0确定,则时钟会按照新调节好的数据开
Status
- VC++6.0调试通过。单文档MFC程序中,随时捕获鼠标的状态,并显示在状态栏中。包括坐标、按键、时间等状态信息
danpianjishiyandaima
- 单片机中按键显示实验源代码,可以为刚刚接触单片机课程的学生或技术人员提供参考和帮助-Button to display the microcontroller experiment source code, can provide information and help just contact MCU student or technician courses