搜索资源列表
SK51
- 此PDF文件为一51串口下载烧录器电路的PCB图,可直接打印于光面纸上用于热转印制作,对于单片机初学者有一定的实用度.-This PDF document is a 51 serial download burner PCB circuit diagram, can be directly printed on glossy paper used to transfer the production of, for Singlechip beginners have a certain degr
shuxianbiao
- 多功能数显表 本毕业设计的设计任务为一个多功能数显表。该数显表可以测量和显示气压、冲击频率和耗气量。并且具有RS232接口和时间显示。本毕业设计作品选用AK-4气压传感器和LWGY涡轮流量传感器,通过MCS-51单片机来控制操作,实现信号数据的采集、处理和发送。本毕业设计作品不仅可以将气压、冲击频率、耗气量及时间等数据显示在8个LED数码管上,还会通过RS232串口,将数据发送到PC上。并由PC上的配套程序,将信息数据显示在显示器上,这两部分所显示的数据是完全相同的。其中数字显示时间单位为秒
8051CommunicationASM
- 利用MCS-51汇编语言实现的单片机通信程序,包括利用P1端口设定信号发送和接收,利用串口实现收发通信,单片机和主机通信等等。-Use of MCS-51 microcontroller assembly language communication program, including the use of P1 port setting signals to send and receive, send and receive communications using the serial
gpsPproteusP52
- 本系统采用51单片机为处理器以带字库的12864或1602液晶显示作为人机对话接口,硬件部分主要采用GPS模块、STC89c52RC单片机、1602液晶显示器或带字库的12864液晶显示器等组成,GPS模块发送的串行数据送至单片机串行口,经单片机处理后送到液晶显示器进行显示。-The system uses the font of 51 single-chip processor to 12864 or 1602 LCD as the man-machine dialogue interface
CH452
- 程序功能为51单片机通过三线串口操作CH452,CH452驱动8位数码管正常显示以及显示数据的更新。51单片机通过模拟CH452串口操作时序向-The program features 51 microcontroller via a three-wire serial interface operation CH452, CH452 driver 8 digital tube display properly, and display data update. 51 single-chip C
jackchuankuofor51
- 用labview2011设计的关于51单片机和labview串口通信-51 single-chip design with labview2011 labview serial communication
lesson7_3
- 基于51单片机的串口程序,调速通过,挺好用的,大家可以-Based on 51 single-chip serial procedures, the governor through very good use, we can try
IO
- 51系列单片机普通的IO 口模拟串口通信,已经过测试,可以直接使用-51 Series single-chip analog IO serial communication, has been tested, and can be used directly. . .
MCU_PC_communication
- 采用串口通讯,实现PC机与下位51单片机通信-PC exchange date with MCU through serial port.
MCU-and-Bluetooth-module
- 51单片机与蓝牙模块的串口通信基于单片机的蓝牙接口设计及数据传输的实现-Serial communication51 MCU and Bluetooth module
shangchuan
- 上传程序为基于51单片机的实例操作程序,含有继电器控制,液晶显示,传感器控制以及串行口通信的程序代码-Upload program is based on 51 single instance of operating procedures, containing relay control, LCD display, sensor control and serial port communication program code
23953391283b
- 51单片机实现单片机与PC机的串口通信中需要的所有的资料-All information 51 MCU MCU and PC serial communication needs
51chengxu
- 51单片机开发程序源码,里面有串口程序源码,温度传感器源码,是个很好的资料。-51 MCU development program source code, there is a serial program source code, source temperature sensor, is a very good information.
DHT11_serial
- 将dht11的c代码转换为asm,并在51单片机上通过串口成功传输到电脑。-Converts dht11 c code to asm, and through a serial port on 51 single chip microcomputer successfully transmitted to the computer.
51asm
- 51单片机基础大量汇编语言源代码,流水灯、简单键盘、数显、串行口、中断实验、红外-Lot 51 microcontroller assembly language source code base, water lights, simple keyboard, digital, serial port, interrupt the experiment, infrared, etc.
MFRC522_C51
- 实现RC522与单片机的通信连接,这里可以用c语言keil环境编写51单片机控制RC522射频卡读取卡号,通过串口显示-use 51 to RC522
Serial-to-parallel-conversion
- 利用MCS-51单片机的串行口和串行输入并行输出移位寄存器74LS164,扩展二个8位输出通道,用于驱动二个数码显示器,在数码显示器上循环显示从8031串行口输出的0—9这10个数字。-Use MCS-51 microcontroller serial port and the serial input parallel output shift register 74LS164, extend two 8 output channels to drive two digital display
123
- 遥控解码通过电脑串口显示,51单片机程序,适合初学者下载-Remote display decoded by the computer serial port, 51 microcontroller program for beginners download
Simulate-the-elevator-system
- 这是一个labview的应用实例,主要功能是模拟电梯工作系统,里面还应用了LED矩阵滚动屏,和数码管显示楼层。用Labview做主机(电梯梯轿主控制面板),protues仿真51单片机做从机(各楼层控制面板),串口通信,实现电梯工作系统的模拟-This is a labview application examples, the main function is to simulate the elevator system, the LED inside the application mat
51UsartCode
- 用51单片机写的串口通信代码,用来参考,c代码-51 microcontroller and serial communication codes