搜索资源列表
main
- 本次利用液晶扩展板(开发板)两个按键(S6、 S7)分别控制 CC2430 模块两个 LED灯亮灭。 -The use of LCD expansion board (board) two buttons (S6, S7), respectively, control the CC2430 module two LED lights off.
LCDtimer
- 运动计时器的设计。设计要求: (1)在液晶显示屏上显示分钟和秒,最长的计时时间为59:59。 (2)按下清零按键,在液晶显示屏上显示的时间为00:00。 (3)按下启动/暂停按键,则启动或暂停计时器计时。其功能与实际的计时器的开始/停止按钮功能相同。 -Movement timer design. Design requirements: (1) in liquid crystal displays minutes and seconds, the longest time 59
yejing0~99jishuqi
- 89C51单片机 1602液晶显示0~99计数器-89C51 Singlechip 1602 LCD 0 ~ 99 Counter
AN202SW
- 这是C8051F330的LCD驱动程序,已经测试过了-C8051F330 This is the LCD driver, has tested the
08-09
- 单片机万年历 文 件 名:万年历设计.c * 功 能:我的小制作-------万年历 **************************************************************************/ /****************************文件包含*************************************/ #include < reg52.h > #include < ch
LCD_data
- for lcd hd44780 life good winxp
volt
- Program in C (CCS to compiler) for the PIC16F84. It is a voltmeter 0 to +5 volts that dispaly the reading in a screen LCD-Program in C (CCS to compiler) for the PIC16F84. It is a voltmeter 0 to+5 volts that dispaly the reading in a screen LCD
gen
- Program in C (CCS to compiler). It is a thermometer with scales in degrees Celsius and Farenheit. Reads a sensor (2N3004 like diode) and using a ADC0831 connected to a PIC16F84, it captures the value, calculates the temperature andt displays it on a
ntc
- Program in C (CCS to compiler). It is a Program in C (CCS to compiler). It is a thermometer realized with a PIC16F84 and a NTC. The time of load of a condenser of fixed value is moderate. The table of the resistance of the thermister versus the time
LCDBIAO
- sed1335驱动320x240图形液晶驱动演示程序320x240液晶模块配用sed1335驱动接口板,sed1335驱动接口板上配用32K ram -320x240 graphic LCD driver sed1335 demo driver with 320x240 LCD module interface board with sed1335 drive, sed1335-driven interface with on-board with 32K ram
LCD_4_bits_mode
- Source code for lcd display 4 bits mode for pic16f877 using CCS.
lab4
- 使用8051控制 LCD display.-Using the 8051 to control the LCD display.
glcd2
- lcd based programming for 8051 users
cewen
- 单总线多点测温系统,单总线它采用单根信号线既传输时钟又传输数据,而且数据传输是双向的它具有节省I/O 口线资源结构简单成本低廉便于总线扩展和维护等诸多优点。本系统中所有的DS18B20都接在单片机的P1.1口上。用一个液晶屏显示,从单片机P3口接上8个开关,与右边的DS18B20 编号对应。当没有开关按下时屏幕显示"which NO you want press which key",要想看那一点处的温度就按下几号键-Single-bus multi-point temperature meas
lcd_pad
- Lcd interfacing using code vision avr
lcddisplayprogram
- 液晶显示程序 并行和串口传输 可显示字符 字符串 整数 汉字 图形等-lcd display use c program it included two ways for dilivering data string char COCK Golden Palm TECH
12864
- 8051 C51示例程序,LCD液晶屏显示-c8051f
ATMega8-LCD_T
- Atmega8 avrstudio project (Multimeter, thermometer, 2x16 LCD with custom char, include: Schematics) Working example with photo-Atmega8 avrstudio project (Multimeter, thermometer, 2x16 LCD with custom char, include: Schematics) Working example with p
VHDLofcontrolLCD
- VHDL for LCD control -VHDL for LCD contral
timer0
- hi i am presenting timer source code with LCD program. I am use timer0 which is 8 bit timer and it start count and result display on LCD.-hi i am presenting timer source code with LCD program. I am use timer0 which is 8 bit timer and it start count a