搜索资源列表
rtc
- RTC读取 系统时钟设计 数码管点亮 I2C 实现-RTC读取 系统时钟设计 数码管点亮 I2C 实现
8weishumaguan
- 单片机控制8位数码管,有仿真图,方便修改。-SCM control 8 digital tube simulation diagram, and easy to modify.
loop-display-source-
- 单片机小实例一百个中的基础部分,单只数码管循环显示,源代码-MCU small example of part of the basis of one hundred single digital control loop display source code
c.hex
- 数码管显示的温控电机设计与仿真,这是c语言程序。是完整的程序-Digital tube display of temperature control motor design and simulation
1616led-
- 详细说明:1. LED的显示原理: 16×16扫描LED点阵的工作原理同8位扫描数码管类似。它有16个共阴极输出端口,每个共阴极对应有16个LED显示灯-Detailed descr iption: 1. LED display principle: 16* 16 scans the working principle of LED dot matrix with eight scanning digital tube. It has 16 of cathode output port, eac
pedometer
- 本文设计了基于加速度传感器的计步器,并通过仿真以及实际调试得到了相应的结果的记录。本实验首先通过加速度传感器检测目标物体的运动,产生脉冲,将脉冲放大后经过施密特触发器整型为方波,并给出了方波的调试电路图。然后编写程序,利用D触发器检测方波的上升沿,当上升沿到来时,计数,并对十位、个位分别编码,然后由使能信号交替控制数码管输出结果。本文给出了仿真以及调试的程序、结果。-This article is designed pedometer-based acceleration sensor and
shuzi
- 数字秒表单片机控制,按钮控制显示,数码管断码口使用P0-The digital stopwatch MCU control, button control, digital tube breaking yards mouth use P0
aaa
- 数码管显示扫苗,I/O口的定义,定时器的使用-The digital display sweep seedlings, as defined in the I/O port, timer use
ourdev_599970AZGFDT
- 一个icl7107的proteus仿真电路,内含4个共阳数码管。-A icl7107 proteus simulation circuit, containing a total of four digital seg.
51
- 51单片机 ntc热敏电阻测试数码管显示-51 single-chip the thermistors testing digital tube display
PWM
- PWM方式控制发光二极管的亮度 说明: 按钮控制PWM输出,使P4.1的发光二极管(数码管的b段),由亮到灭分为8级控制,一个 按钮增加亮度,另外一个减少亮度,数码管显示亮度等级,P1.0 控制变亮,P1.1控制变暗. - PWM mode control the brightness of the light emitting diode Descr iption: button control PWM output, make P4.1 led (light emittin
AD
- 使用AD单通道多次转换,采集P6.0输入的模拟电压值(变化范围:0~将P6口输入的模拟电压AD转换后,从P4、P5口连接的数码管输出。 使用AD单通道多次转换,采集P6.0输入的模拟电压值(变化范围:0~3.3V),转换为数字量。 建立二维数组和通过顺序查表的方法得出采集回来的电压值。然后通过数码管显示当前电压值,显 示跟随输入的模拟电压的变化。由于只有两位数码管,故显示电压值精确到小数点后一位,如当前 输入电压2.37V,则显示2.4V。可用万用表检测显示是否准确。 -U
Eight-digital-tube-displays-scan
- 八位数码管显示扫描,用于显示数字或者字母等-Eight digital tube displays scan, used to display numbers or letters, etc.
GX_BOARD
- FPGA设计参考电路(SDRAM,SD卡,USB,数码管,I2C,ram)-FPGA design reference circuit (SDRAM, SD card, USB, digital tube, I2C, ram)
DS18B20
- DS18B20温度控制数码管显示 (汇编非常详细) - DS18B20
51serial-communication
- 51单片机c语言串口通讯编程,包含数码管的串行驱动-51-singlechip serial communication and CAMAC serial driver CAMAC for LED
main
- 将两块CAN总线开发板CANH---CANH,CANL---CANL相连连接无误后分别按动中断按键。相应的数码管显示加一,并通过CAN总线发送到另一块数码管上显示。-Two CAN bus development board CANH--- CANH, CANL--- CANL connected connected to the correct respectively pressing the interrupt button. Corresponding digital display p
main
- CAN开发板-数码管显示中断计数,每按一次中断按键,计数值加一,在数码管上显示。-CAN development board- digital tube display interrupt count, the count is incremented each time you press the interrupt button on the digital display
main
- CAN开发板-CAN自收发实验,数码管从右到左分别是1~4位。数码管1、2位显示发送的数据,3、4位显示接收到的数据。每按一次中断按键发送数据值增一。--CAN CAN development board self-transceiver experimental digital tube from right to left are 1 to 4. 1,2 bit digital tube display data sent, 3,4-bit display data received. Ea
main
- 将两块CAN总线开发板CANH---CANH,CANL---CANL相连,通过串口调试软件发送数据到单片机中,数码管显示相应的数值,并通过CAN发送到另一块CAN开发板上。-Will be connected to two CAN bus development board CANH--- CANH, CANL--- CANL debugging software to send data through the serial port to the microcontroller, digit