搜索资源列表
nannvshengshibie
- 本文通过对男性和女性声音的语音特征的研究,发现男女声的基音频率存在较大的差异,并设计了基于基音频率分析的男女声识别系统。男女声识别系统由以下三个模块电路构成:话筒放大器,低通滤波器,半波整流电路,单片机测量控制模块。话筒放大器采用NE5532P音前置芯片,对语音信号进行放大;八阶低通滤波器MAX293完成基音信号的提取;单片机STC12C5410AD实现频率测量和控制输出功能。经仿真与电路实测,男女声的识别效果良好。-In this paper, the voices of male and f
05
- 了解微波滤波电路的原理及设计方法。 学习使用ADS软件进行微波电路的设 计,优化,仿真。 掌握微带滤波器的制作及调试方法-Understanding of microwave circuit theory and filter design methods. Learning to use software ADS microwave circuit design, optimization, simulation. Mi
113f
- 基于Proteus环境下信号发生器的电路仿真实验设计,大家可以参考-Proteus environment based on the signal generator circuit simulation design, we can refer to! ! ! !
proteus
- 详细讲解了数字电路,模拟电路,控制电路系统以及外设的组合系统的设计和仿真,以及PCB设计-Explain in detail the digital circuitry, analog circuitry, control circuitry and peripheral combinations systems design and simulation, and PCB design
Proteustaxi01
- 本文以出租车模拟计价器设计的实例, 详细介绍了Proteus 的特点、使用方法以及Proteus 在单片机系统硬、软件开发与 仿真的应用, 它能有效提高工作效率, 对于单片机应用系统、电子电路的开发和教学等都有较大的实用价值。整个设计过程 表明了该软件在实际系统开发中的有效性和实用性。-In this paper, analog meter taxi design examples, detailing the features of Proteus, using methods and
bjt-model-and-parameters
- bjt 模型和参数说明 方便在hspice软件下自建model进行电路仿真-bjt model and parameters to facilitate self-built model in hspice software for circuit simulation
repetitive-control-for--inverter
- 分析了电压型控制模式下的逆变器并网的电路结构和数学模型,提出了基于重复控制技术的光伏逆变器并网控制策略,仿真和实验结果表明方案满足逆变器并网要求。-Voltage control mode inverter grid circuit structure and mathematical model is proposed based on repetitive control technology photovoltaic inverter grid control strategy, simu
matlab
- 设计一个一位二进制数大小比较器。比较两个一位二进制数A和B的大小,电路有三个输出端Y1,Y2和Y3,分别对应A大于B,A等于B,A小于B。当条件满足时,相应输出端为1,否则为0。(A,B用两个脉冲源代替),建立仿真模型并保存。-Design a one binary magnitude comparator. A size comparison of two binary numbers A and B, the circuit has three outputs Y1, Y2 and Y3,
matlabs
- 设计一个两位二进制数大小比较器。要求当二进制数A=A1A0大于二进制数B=B1B0时,电路输出为1,否则为0(A1,A0,B1,B0用四个脉冲源代替),建立仿真模型并保存。-Design a two binary magnitude comparator. Required when the binary number is greater than the binary number A = A1A0 B = B1B0, the circuit output is 1, otherwise 0
protues
- 郭天祥开发板仿真电路。本仿真图是郭天祥开发板的原理图,可自行更改部件-Guo Tianxiang development board simulation circuit. This simulation map is the Guo Tianxiang development board schematics, can change their own components
PSIMIntroductory-tutorial
- 此文档为PSIM仿真软件的入门使用教程,PSIM是专门用于电力电子电路仿真的软件。-This document is for the PSIM simulation software of introductory tutorial, PSIM is specially used in power electronic circuit simulation software.
Water-lamp-design
- 1、设计能带8个LED发光管发光,并按照要求轮流发光,产生流水灯的流动效果。 2、应具有两种以上不同风格的流动闪亮效果。比如依次点亮或者依次熄灭。(选作) 3、有起动、停止控制键。(选作) 4、有流动闪亮效果选择设置键。(选作) 5、对所编写的电路进行编译及正确的仿真。-1, designed to bring eight LED light tube light, and in accordance with the requirements of the light-emit
Chen-system-synchronaziton
- 基于波特图的频域近似方法,研究了分数阶)*+ 混沌系统,并设计了一种树形电路单元来实现分数阶)*+ 混沌 系统,通过对&,! 阶)*+ 混沌系统的电路仿真和实验,以及!- #,.—#, (步长#, ))*+ 混沌系统的电路仿真,验证了 树形电路单元的有效性,证实分数阶)*+ 混沌系统中确实存在混沌现象,且存在混沌的最低阶数为#,/0 设计简单 有效的线性反馈控制器,实现了分数阶)*+ 混沌系统的混沌控制0-Bode plot approximation method based on
A-new-four-dimensiona
- 基于波特图的频域近似方法,研究了分数阶)*+ 混沌系统,并设计了一种树形电路单元来实现分数阶)*+ 混沌 系统,通过对&,! 阶)*+ 混沌系统的电路仿真和实验,以及!- #,.—#, (步长#, ))*+ 混沌系统的电路仿真,验证了 树形电路单元的有效性,证实分数阶)*+ 混沌系统中确实存在混沌现象,且存在混沌的最低阶数为#,/0 设计简单 有效的线性反馈控制器,实现了分数阶)*+ 混沌系统的混沌控制0-Bode plot approximation method based on