搜索资源列表
c1101
- 直流电机的测速调速模块,运用光电传感器测速,L298芯片调速-DC Motor Speed Control Module, the use of photoelectric sensor gun, L298 chip speed
Text1
- 一款用于51单片机的红外遥控小车程序(L298)-Infrared remote control car program (L298
Forword
- 基于51单片机的使用,运用2个L298配合驱动步进电机程序源码-Based on the use of 51 single-chip microcomputer and using two L298 driving a stepper motor program source code
MOTOR-C
- 基于C51的脉宽调制控制直流电机转速,设计采用LCD1602作为显示器,实时显示转速。设计采用L298你作为电机驱动,带保护电路-Based on C51 pulse width modulation control DC motor speed, design using LCD1602 as a display, real-time display speed. Design using L298 you as a motor drive, with a protective circuit
pwm
- atmgega128PWM例程,用应于L298驱动的电机-atmgega128PWM routines should be used to drive a motor L298
基于51单片机直流电驱动设计
- 本设计是以单片机AT89S52和L298控制的直流电机脉宽调制调速系统。利用AT89S52芯片进行低成本直流电动机控制系统的设计,能够简化系统构成、降低系统成本、增强系统性能、满足更多应用场合的需要。系统实现对电机的正转、反转、急停、加速、减速的控制,以及PWM的占空比在LCD上的实时显示
dianjizhuansu
- 用51单片机输出pwm的占空比控制电机转速(The output speed of PWM is controlled by 51 single-chip microcomputer, which is controlled by duty cycle)
PWM电机 - 副本
- 驱动直流电机,通过l298n来驱动,stm32板拉高引脚PA9与PA10,同时PA7输出PWM值(The drive DC motor is driven by L298N, the STM32 board pulls the high pin PA9 and the PA10, and the PA7 outputs the PWM value)
自平衡
- 该代码为自平衡小车代码校车使用的是430做处理器,MPU6050,1:90大扭矩电机, L298驱动,2576稳压,用的平衡互补滤波和PID(The code for self balancing car code, the school bus is used as 430 processor, MPU6050,1:90 large torque motor, L298 drive, 2576 voltage regulator, with the balance of complementa
步进电机资料
- 步进电机的试用和说明,单片机控制,L298进行驱动(Stepper motor trial and explanation, microcontroller control, L298 drive)
风力摆控制系统源代码
- 风力摆自动控制,两个L298电机驱动模块控制直流风机的转速(Automatic control of wind pendulum)
驱动
- 驱动直流电机工作,很多专门的电机驱动ic,如L298,33886等,其内部主要还是采用的H桥电路,用起来比较方便。同时也有可用分离元件来设计H桥驱动电路,其驱动能力强。(Drive the work of DC motor)
直流电机速度PID控制
- 光电编码器测得的电机速度反馈信号反馈到单片机中。电机设定速度由ZLG7289模块获得,通过SPI通信传输给单片机。单片机系统根据给定的转速与反馈回来的实际速度相减得出偏差,经过控制算法得出控制量。单片机再把控制量以PWM的形式输出,经过L298功率放大驱动直流电机。ZLG7289模块主要用于显示当前直流电机实际转速和给定转速,并让用户通过键盘输入设定速度。(The motor speed feedback signal measured by the photoelectric encoder