搜索资源列表
12864A-1
- 12864A-1汉字图形点阵液晶显示模块使用手册-12864A-1 character dot-matrix graphic LCD Module User' s Guide
18b20_MSP430
- 很好的18b20程序,muc是ti公司的低功耗单片机MSP430f149,加1602显示的,可以直接用-it‘s a code which based on the chip of msp430f149,with the lcd of 1602
LMS480KF01_PI_General_Rev001.pdf.tar
- 800 * 480 24bit RGB LCD Module Data Sheet. LMS480KF01-800* 480 24bit RGB LCD Module Data Sheet. LMS480KF01
SOPC_Nios
- Altera SOPC Builder 提供了 Nios Ⅱ处理器及一些常用外设接口 ,但并没有提供 12864 液晶模块的接口及驱动。-Altera SOPC Builder provides the Nios Ⅱ peripheral processor and a number of commonly used interface, but did not provide 12864 LCD module and the drive interface.
3510I
- 本程序是3510I液晶的读写与画点,希望对大家有用-This procedure is 3510I LCD reading and writing and painting in the hope of useful
lcd
- lcd显示,按键扫描,相应键显示相应数值-lcd display, keypad scanning, corresponding to display the corresponding numerical
LCD
- lcd controller using vhdl code
Proteus-Model-Nokia3310LCD
- vsm model for nokia lcd 3310
lcd
- LCD字模提取及显示在LCD上,LCD刷屏-LCD
LCDTV_FirmwareDesignFrame
- 内部资料液晶电视软件概要设计,液晶电视软件工程规划-Internal data summary of the design software, LCD TV, LCD TV software project planning
MMC
- Nokia 6100 LCD Display Driver SPI
ADC
- ads1.2环境下LPC2148驱动12864液晶显示ADC转换结果-ads1.2 environment LPC2148 Driver 12864 LCD ADC conversion results
mtkdrive
- mtk驱动其实不难,每个做mtk的公司的驱动工程师可能都有这样的感受:我是个打杂的 - -! lcd的调试一般是这样:首先是客户提供lcd模组和一些lcd驱动芯片的初始化代码,休眠代码,可能还有写窗口代码的寄存器的值。我们拿到这些代码后,如果之前有调好的类似大小的lcd的驱动代码,就可以借用这个模板,如果没有另说。一般都有往寄存器写数据的函数,直接copy,按照模板,可以把客户提供代码全部放进去后,正常情况下(lcd和pcb在硬件上相同,数据传输的数位相同),屏都是能点亮的,可能会有些
lcd
- Write the 8085 ALP driver program for the 16X2 LCD display. Use it to display any message
Interfacing_LCD_Panels071607a
- how to connect your board with LCD(TFT) panel pins by Sharp
lcd1602verilog
- verilog lcd液晶1602驱动 这个程序的显示字符显示的是ASCII码,显示的数据由DB8输出到LCD上-verilog
f84lcdtach
- spi file mst717 lcd tv
LCD
- C source code for 4*20 character LCD , winstar WH2004L
KS0108_Complete_Commands
- I2C LCD 128 x 64 Graphic BV4512. It presents a detailed I2C Command set of LCD display.
KS0108-Commands-07540902
- LCD GRAPHIC MODULE with 128x64 dots. It includes pinout, timming characteristics and instruction set of KS0108 display. It can be easily controlled by AVR or PIC microcontrollers or by parallel port.