搜索资源列表
SyncRGB1210
- 这是一块红外遥控RBG灯的控制软件，采用单片机是STM8S103F3P6，可以检测如果交流信号具有可以同步，如果是直流信号就按内部的时间来变化-This is an infrared remote control software RBG lamps, using SCM is STM8S103F3P6, can detect if the communication signals can be synchronized, if the DC signal to change by the t
STM8S103F6-ZH-power-F001-V1.1.1
- 电源转换器源码： 主芯片STM8S103F3P6,TSSOP-20 多路开关控制，PWM斩波，外部过流中断保护功能，上电自检测功能等-Power source: The main chip STM8S103F3P6, TSSOP-20 Multi switch control, PWM chopper, the external current interruption protection function, power on self test function
STM8S103F3_1
- stm8s103f3p6说明书，主要是介绍该芯片的资料的使用手册-stm8s103f3p6 Manual
STM8-IAR
- stm8s103F3P6单片机测试程序大合集-Large collection stm8s103F3P6 SCM test procedure
STM8-005_OLED_12864
- STM8S103F3P6液晶程序，OLED-12864驱动程序-STM8S103F3P6 LCD procedures, OLED- 12864 driver
renesas_usb_3.0.23.0
- 使用高性价比单片机STM8S103F3P6读取三轴陀角速度计芯片L3G4200D的值,并进行滤波然后串口输出-Use of high performance chip STM8S103F3P6 read the three axis of the value of the chip L3G4200D, and then filter and then serial output
SPWM_T2
- STM8S103F3P6，定时器2输出SPWM波形，使用中断查表方式。-STM8S103F3P6, timer 2 output SPWM waveform, using interrupt way of look-up table.
STM8S103F3P6-LED
- STM8的经典例程,在STM8S103F3P3上跑通，开发环境IAR，需要的拿走-stm8 demo,you must like it
rf433
- 这是个完整工程，使用rf433/315M超再生模块(最便宜那种)通讯的接受程序。可以用电脑串口接发射模块按照doc文件夹里的说明编码实现通讯测试。可实现短距离传感器数据采集等。MCU为stm8s103f3p6, 编译环境为IAR for stm8.-Here s a completed project.RX decode using rf433/315Mhz super-regeneration moduler(yes,the cheapest one!). You can use PC to
LED
- STM8S103F3P6最小系统测试程序：驱动LED闪烁(STM8S driver LED flashing)
STM8S103F3P6产生两路互补PWM波配置
- 搞了两天，总算使用STM8S103F3P6最小化系统板的TIM1产生两路互补的PWM波，现拿出来分享一下。工程为IAR环境，寄存器配置。(For two days, we used the STM8S103F3P6 to minimize the TIM1 of the system board to produce two complementary PWM waves, and now to share it. The project is IAR environment, register
STM8_模拟串口接收（接收单个字节完成）
- 利用STM8S103F3P6的普通IO口设计UART功能，波特率可以达到250Kbps,能够稳定的接收单字节数据并通过串口输出。模拟串口的发送也可以达到250Kbps.(Using STM8S103F3P6 general IO mouth design UART function, baud rate can reach 250 KBPS, can receive stable single-byte data and output via a serial port. Simulation
EasySTM8S103 EEPROM字编程
- stm8s103f3p6按字读写EEPROM(read EEPROM by word of stm32f103f3)
2.配套源码_寄存器版本
- STM8S103F3P6寄存器版本所有程序 UART SPI I2C(STM8S103F3P6 register version, all programs UART SPI I2C)
stm8_rc522-master
- STM8S103F3P6核心板 + RC522模块 调试正常(STM8S103F3P6 Core Board + RC522 Module Debugging Normal)