搜索资源列表
OLEDSTM32
- OLED STM32 驱动显示方法 8080通信，MDK文件系统，图片字符的显示设置与驱动
CX_A8_232
- stm32驱动OLED显示AD端口电压(The STM32 drive OLED displays the AD port voltage)
体感控
- 通过mpu6050的角度来进行对飞行器的控制，将欧拉角投射到oled屏上(use the mpu6050 to control the flight)
DHT11
- stm8s103P , 控制DHT11，采集温湿度，OLED显示(stm8s103P,DHT11,OLED12864)
中景园电子0.96OLED显示屏_C51系列_IIC_例程
- 0.96OLED显示屏c51系列IIC例程(0.96OLED display C51 series IIC routine)
esp8266_deauther-master
- arduino编程的wifikiller 使用芯片组为ESP8266 系列（12N/12F等）；可以为外接显示屏，OLED 屏幕IIC接口，VCC-3.3 GUN-G,SDA,SLC接口代码中可随意修改，使用前下载好库文件，arduino库中有。(Arduino programming wifikiller uses chipset as ESP8266 series (12N/12F, etc.); it can be modified for external display, OLED s
program
- oled显示的基于CC2540的花卉喷灌系统(OLED based flower sprinkler system based on CC2540)
12864
- STC单片机的0.96寸，OLED128*64驱动(STCmcu 0.96 OLED128*64 driver)
PM-F103-16MHZ
- 基于STM32F103C8T6芯片，串口解析数据，OLED显示程序(Serial port parsing data, OLED display program)
大棚控制—STM32
- 大棚环境监测系统，esp8266 +AM2303+MQ-2 数据通过Android上位机接收，OLED本地显示传感器数据(The greenhouse environment monitoring system, the esp8266 +AM2303+MQ-2 data is received by the Android host computer, and the OLED local display sensor data)
430-oledV2
- masp430硬件iic驱动oled，关于底层寄存器配置和操作(Masp430 hardware iic drives oled.)
人体红外传感器实验代码
- 巡线传感器根据是否有人经过，采集到人身体上的红外信号，实现 FS_11C14 V6.0 开发平台上的 OLED 屏显示不同的信息。连接好模块，上电运行。用手在人体红外传感器的小白色胶盖前面运动，则LED1灯会亮。(The line sensor can collect the infrared signals on the human body according to whether someone has passed, so that the OLED screen on the FS_1
ACT6311
- 此资料是讲解了ic升压的部分，满足led需要的电压，特别是oled(This information is to explain the part of the IC boost to meet the voltage required by LED, especially OLED)
单片机程序
- 基于STC12C5A60S2的智能花盆设计,过单片机实时检测花盆温度，土壤湿度，光照强度，并显示在oled屏上，控制对应的继电器开关的通断，实现对温度、光照、土壤湿度的调节。已配置好 WIFI模块ESP8266，可将温度，湿度，光照强度等数据发送到云服务器。(Based on STC12C5A60S2 intelligent flower pot design, MCU real-time detection of flowerpot temperature, soil moisture, li
main
- GPS时钟 51单片机(gps)
nrf24l01多发一收
- 实现两个Nrf24l01发送，一个接收,然后将采集到的温度·数据发送到Mcu,mcu在oled屏幕上显示(Implementing two Nrf24l01 sending, one receiving, and then sending the collected temperature and data to Mcu, and MCU on the OLED screen)
OLED_SPI
- 这是SPI协议的OLED驱动代码,适合初学者学习.(This is the OLED driver code of the SPI protocol, suitable for beginners to learn.)
恒温烙铁源码
- 1.8寸OLED屏显示的源码，已通过KEIL检验，压缩包里面有详细说明。
sim800a02061643_con_all_ok
- 用STM32单片机采样DHT11的温度和湿度数据,并使用OLED显示;(Sample DHT11 temperature and humidity data with STM32 single chip, and use OLED to display it.)
ESP8266_SSD1322-master
- small library for ssd1322