搜索资源列表
resource_5081132_1326961393q
- 串口打印，使用serialPort实现无驱动串口打印-com print
keil-ZigBee-cortex_m0
- cortex_M0 实验板的 ZigBee 模块通过 SPI 总线与 LPC11C14 相 连， 数据由 ZigBee 接收后， 先由 ZigBee 传输给 LPC11C14 进行处理， 然后通过 OLED 显示，以及经过串口在串口调试助手中打印-cortex_M0 experiment board ZigBee module is connected via the SPI bus with LPC11C14, after receiving data from the ZigBee,
ADC_UART
- 嵌入式处理器，开发6410，能实现串口测试，打印ad信息-Embedded processor 6410, development, can realize serial port test, print AD information
STM32F407-led
- STM32 usar程序，改程序实现LED流水闪烁，和串口打印功能-STM32 usar program, change the program to achieve LED water flashes, and serial print function
F00x_UART0_STDIO
- c8051F00串口驱动程序,实现串口打印-c8051F00 serial driver, serial print
ESCPOS_Sample
- ESC打印机命令集 对打印开发有帮助 串口打印机-ESC printer command set of the print development help
ustar1
- stm32通过串口与PC实现通讯 在PC上打印出所需要的信息-stm32 achieve communication with the PC via the serial port on a PC to print out the required information
STM32-IIC--MMA8451
- STM32的控制MMA8451三轴加速度芯片的IIC驱动，串口打印数据到电脑显示！-STM32 control MMA8451 the triaxial acceleration chip IIC driver, serial print data to a computer display!
STM32--SD-RW
- 开机先初始化SD卡，如果SD卡初始化完成，则读取扇区0的数据，然后通过串口打印-Boot initializes the SD card, if the SD card initialization is complete, the read sector 0 of the data, and then print through the serial port
SerialFiltration_DDK
- 串口过滤驱动，只是简单地打印出通过串口上的信息-Serial filter driver, but simply have to print out the serial port information
03_RTC(3.2)
- 1、首先用串口线将USART1与PC连接 2、通过JLIK下载后 按下复位键S4，程序开始运行 3、LD1闪烁 TFT显示蓝色字符串 “FireBull RTC example” 4、超级终端打印信息“Please Set Hours” 键入“12” 打印信息“Please Set Minutes” 键入“10” 打印信息“Please Set Seconds” 键入“10” 完成人机交互，输出时间 Time：12：10：10-1, first of all
IRQ_
- S3C2440 裸机中断程序，当有按键中断时，利用函数uart_printf() 向串口打印一些信息，同时led灯显示-S3C2440 bare interrupt program, when a button is interrupted, using the function uart_printf () print some information to the serial port, and led lights display. .
GPS
- norflash运行，串口打印GPS数据-norflash run, serial print GPS data
nandflash_demo
- 该实验程序完成了land flash的读写测试，包括串口打印输出功能，适用于fl2440，ok2440上的k9f**（2K） nand falsh读写实验代码-The experimental procedure is completed the land flash read and write tests, including serial print output for fl2440, ok2440 on k9f** (2K) nand falsh experimental code r
MMC_SD
- 本实验将实现如下功能：开机的时候先初始化SD卡，如果SD卡初始化完成，则读取扇区0的数据，然后通过串口打印到电脑上。如果没初始化通过，则在LCD上提示初始化失败。 同样用DS0来指示程序正在运行。-The experiment will achieve the following functions: boot time to initialize the SD card, if the SD card initialization is complete, the data is read s
SD
- 基于STM32的SD卡(SDIO模式)测试实验，并将测试信息通过串口1在电脑的超级终端上打印出来-Based on the STM32 SD card (SDIO mode) testing laboratory and a test message via the serial port on the computer print out HyperTerminal
Monitor
- Dsp的pc端的监控程序，使用串口通信，包括变量查看，内存查看，打印-Monitoring program Dsp PC side, the use of serial communication, including the variable view, memory view, print
USBReadDir
- USB主控制芯片CH375，读取U盘根目录信息，通过串口打印出来，希望对使用CH375的朋友有帮助-USB host controller chip CH375, read U root directory information through the serial print it out, I hope to help a friend with CH375
GPS_LEA6H_NMEA_protocol
- 用STM32接收GPS信号，设备采用NMEA协议，接收后将ASCII码转换成数值，同时分解协议内容，并通过串口打印到上位机上-With STM32 GPS signal reception equipment using NMEA protocol, the receiver will convert the ASCII code value, while decomposition agreement, and print to the PC through the serial port o
tiny6410_key_int_uart
- 开发环境为RVDS4.0，基于开发板Tiny6410，裸机程序，该程序涉及内容按键、中断、串口打印。 按键通过外部中断方式来控制，且串口打印按键信息；当按下K1，串口打印：Key1 is push down!，然后四个用户led显示为流水灯；当按下K2，串口打印：ey2 is push down!，然后led全灭；当按下K3，串口打印：Key3 is push down!，然后led全；当按下K4，串口打印：Key4 is push down!，然后beep响一声；-Development en