搜索资源列表
小车避障
- 这是一个用汇编写的8051单片机系统的小车避障程序，是用红外发射和接收的方式，并结合了proteus 6.7，相信对初学者有所帮助-This is a compilation was made with the 8051 System of Dolly obstacle avoidance procedures is the use of infrared transmitting and receiving the way, and coupled with a 6.7 lic sure to
acmftsj_n
- 一个完整且典型的遥控器程序，包括了按键扫描，液晶驱动，红外发射，内有比较完整的备注，到目前为止市面上的同类产品均是采用此架构，采用了NEC3106芯片和编译器，可以从NEC官方网站或跟NEC联系免费索要开发工具，或电邮我也可以提供-complete a typical remote control procedures, including a button scanning, LCD driver, the infrared emission, which have a relatively
HW01
- 试做的第一个红外发射器，有什么问题请多指教-to try out the first one infrared transmitter, what issues please enlighten
Hw_code
- 红外发射接收程序 1.圈数测量:红外一体化接收头，通过外部中断引脚,1个信号加1 2.单位时间:定时器0,提供1s的时间信息 3.显示单元:8位共阴数码管,P0控制数码,P2控制位码 4.根据频率，控制状态-infrared transmitter-receiver 1. Circle Measure : integrated infrared receiver first, through external interrupt pins, a signal plus 1
fashe
- AT89S52的一个红外发射程序，用汇编语言编写，可扩展。-AT89S52 infrared emission of a process that is written in assembly language, which can be expanded.
c8051f020red
- 程序接收红外发射过来的数据，接收解码后由CPU读取,程序运行前将S2都拨到ON.J17短接第一和第二脚。 -procedures for receiving infrared fired up the data after receiving decoders read by the CPU. pre-operational procedures will have to transfer S2 ON.J17 shorted the first and second legs.
hongwanjieshou
- 红外通信是利用950nm近红外波段的红外线作为传递信息的媒体，即通信信道。发送端采用脉时调制（PPM）方式，将二进制数字信号调制成某一频率的脉冲序列，并驱动红外发射管以光脉冲的形式发送出去；接收端将接收到的光脉转换成电信号，再经过放大、滤波等处理后送给解调电路进行解调，还原为二进制数字信号后输出。
IR_receive
- 大家好，我是易北 这是我写的红外接收的程序 此程序是采用测脉宽地方法写的 感觉比那种定时查询的方法要严格的多 经试验完全成功 而且非常可靠 误码率几乎为零 12M晶振 注意，这个程序和我写的红外发射的程序是不匹配的 那个程序不太严格，用别人的定势查询的方法写的程序可以用，但是用这个程序就不行 敬请注意 谢谢支持 QQ：6036725
1234(2)
- 接收译码电路由红外接收放大器、音频译码电路和声控执行电路组成。接收红外二极管应采用与红外发射管配对的管，在收到红外光脉冲后，接收管D1的两极间电阻作与频率相应的变化，由光信号转化为电信号，经VT1和IC1放大-Received by the infrared receiver decoding circuit amplifier, the audio decoding circuit and voice-activated circuit implementation. Should be us
Upload_DownFiles_
- 红外发射接收管典型应用接口电路，包括原理图-Infrared receiver tubes typical applications, including schematics
HONGWAISHOUFA
- 红外收发演示，红外测试程序，用单片机通过发射管发射38K的调制频率码，由一体化接收并解码由发光管显示-Infrared transceiver demo, infrared testing program, microcontroller through the launch tube with the launch of 38K code modulation frequency, from integration to receive and decode from the LED disp
fashe
- 可以启动红外发射头，产生38Khz红外信号，以启动VS0038接收头，接收信号-c language program
yaokong
- 基于单片机的红外遥控发射程序。。用c语言编程-Infrared Remote Microcontroller-based program. . With c language programming
红外解码
- 红外解码，对常用红外遥控发射芯片UPD6121G进行解码，根据接收到波形显示其 32位二进制红外编码数据波形，根据波形下方刻度可查阅每一位为0或1(Infrared decoding, commonly used infrared remote control chip UPD6121G chip decoding, according to receive the waveform display 32 bit binary infrared coded data waveform, ac
stm8s003__V01_IAR
- 采用stm8s003设计的红外发射控制灯程序，此程序已经经过实践，符合要求。(Stm8s003 design of infrared emission control lamp procedures)
发射端程序
- 控制红外遥控器的发射不同频率不同时间的信号(Control the emission of infrared remote control)
红外线遥控Proteus仿真电路+发射+接收程序
- 基于单片机控制平台的用于红外无线遥控控制编码(Infrared wireless remote control coding based on SCM control platform)
20-红外遥控同时发射接收程序
- 红外遥控同时发送接收程序u，内含C和汇编两种语言(Infrared remote control simultaneous sending and receiving program u, containing C and assembler two languages)
28. 红外遥控实验
- 红外遥控器发射红外键值的编码信号，通过红外接收头进行解码，并将解码后的数据通过串口打印(Infrared remote controller emits a coded signal of infrared key value, decodes it through an infrared receiver, and prints the decoded data through a serial port.)
15 红外遥控收发仿真
- 用proteus仿真红外接收，发射，已成功。(Proteus simulation of infrared receiving, launching, has been successful.)