搜索资源列表
hwx
- 红外遥控、红外接收头组成，模拟遥控器。并用LCD显示解出来的码。-Infrared remote control infrared sensor, simulation of remote control and LCD display solutions out yards
infrared
- 使用verilog语言控制CPLD通过红外收发器进行红外通讯，其中simple.qpf为发送端的工程文件，recive文件夹中的recive.qpf是接收端工程文件-CPLD Verilog language to control the use of infrared transceiver through infrared communication, which simple.qpf for the sending end of the project file, recive folde
hw
- 红外发射接收，控制，试验，是理想的教学，学习，开发伙伴-Infrared emission to receive, control, testing, is ideal for teaching, learning, development partners
test1
- 这是一个利用51单片机的两个外部中断收取红外接收管的信号用以控制绕线器张转或反转-This is a use of 51 single-chip charge two external interrupt signal control infrared receiver to control the routing switch device or inversion Zhang
ir500
- SNC539 红外发射接受二合一程序，即发射和接收程序为一个程序，可分别接发射和接收。-SNC539 infrared emission to accept two-in-one procedure, namely, transmitting and receiving procedures for a program can then transmit and receive respectively.
remotept2221
- 红外遥控接收程序，PT2221,很简洁已经成熟使用-Infrared Remote Control Receiver procedures, PT2221, very simple and has been the use of sophisticated
zsMCUshiyanban
- 本实验板的制作原则，简单实用。资源： 8 个LED（闪灯，走马灯，各式花样灯）。4 个数码管（时钟显示，遥控码显示，计数显示等各种显示）。6 个按键（按键扫描，中断，计数器）。 AT24C02（I2C 总线接口实验）。6个接收头（家电遥控器接收，解码）。MAX232（串行RS232 和电脑通迅实验）。蜂鸣器提供各种实验的例程，让初学者轻松学会单片机编程。其中的遥控解码程序，可将红外遥控器的代码显示到LED 上，是遥控开发的好工具。-This experiment the production o
ir
- c51环境下的红外一体化接收解码头文件，装入该头文件后，即可调用文件中的解码数据运用到单片机控制中-C51 environment integrated infrared receiver terminal solution file, into the header files, you can call the file to decode the data applied to single-chip control
receiver
- 最简单的红外接收演示程序 实验芯片： ATmega8515L或Atmega8515 工作频率： 8MHz 编译软件： WINAVR 1.41-The simplest demonstration of infrared receiver chip experimental procedure: ATmega8515L or job Atmega8515 frequency: 8MHz compiler software: WINAVR 1.41
FPGA_based_infrared_receiver_module
- 基于FPGA的红外接收模块，内含代码，采用VERILOG编写。-FPGA-based infrared receiver module, containing the code prepared by the use of Verilog.
infraredrayuncoded
- 本程序用于单片机的串口调试，接收头用HS0038B，把脉冲高低电平持续时间放入40个数组里，可以进行红外解码！-This procedure for single-chip serial debugging, to receive the first use HS0038B, low pulse duration dd 40 array, the decoder can IR!
hongwai
- 该程序是用C语言编写的红外接收与发送的源程序 -The program is written in C with the infrared receiver to send the source code
multifunctionaldigitalclock
- 本设计采用一块单片机（AT89S52）作为多功能数字钟的控制核心，加以温度传感器、红外接收管、蜂鸣器、液晶显示器（LCD1602）、电源电路及其他电路构成。实现了时间设置、闹铃设置、闹铃开和关的功能；LCD显示小时、分钟，有AM、PM指示灯，闹钟就绪灯，闹钟到点蜂鸣器报警，220V供电基本功能。另外，本设计还实现了通过切换键盘显示现场温度，红外停止闹铃的功能。 -This design uses a single chip (AT89S52) as the core controller o
Learningremotecontrol
- 单片机设计的遥控电路，遥控码的脉宽数用红外线接收器解码后送单片机读入，发射时由单片机产生40KHZ红外调制信号送红外线发射管发射-Single-chip design of the remote control circuit, remote control code number of the pulse width decoder using infra-red receiver to read single-chip evacuation, launch generated by sing
hongwaishoufaqi
- 1.功能描述 (1) 能够实现利用红外线实现无线数据的收发； (2) 能够将发送的数据或接收的数据进行显示，或根据接收的命令执行相应的功能。 （程序内以给出了和详细的注释，很容易读懂） -1. Functional Descr iption (1) can be achieved using infra-red wireless data transceiver (2) be able to send data or receive data display, or recei
Remote_Pro
- 实用红外遥控接收，解码程序。已经通过调试。-Practical infrared remote control receiver, decoding procedures. Have passed testing.
fuzahongwai
- 一个复杂的红外控制小灯程序，将红外发射和接收分开来写的程序，独立成两个模块-Infrared control of a complex process of small lights, to transmit and receive infrared separate written procedures, separate the two modules
fase
- 自己编写的一个单片机控制红外发送与接收的红外发射源程序,同时自己也做了一个板实验,是成功的哦-I have written a single chip to send and receive infrared control of the infrared emission source and at the same time also made a plate experiment was a success, oh
Colorful
- PT2262做编码芯片的七彩灯红外遥控控制程序，有注释。-PT2262 encoder chip so colorful lights infrared remote control program, there are notes.
count
- 智能汽车测速用码表，精切到百分秒，检测电路简单，只需一对红外发射接收管和lcd1602便可。-Intelligent Vehicle Speed code table used, the percentage of precision-cut second detection circuit is simple, just a pair of infrared emission will be able to receive control and lcd1602.