资源列表
INT8LED
- 开机8个灯循环， 按p32后暂停，小喇叭响，松开继续循环，中断的典型应用 硬件连接：p1口8路指示灯，喇叭p3.3,按键p3.2-Boot 8 lights cycle, according to p32 after the pause, small speaker sound, release the continuing cycle, interrupted typical application hardware connection: p1 port 8-channel light,
28LED
- p1口八个灯作二进制加法。理解二进值的计算 硬件连接：p1口8路指示灯-p1 mouth 8 lamps for binary addition. Understand the value of the calculation of binary hardware connection: p1 port 8-channel light
honglv
- * 十字路口红绿灯控制器 * * 第一个状态：主干道、支干道均亮红灯5S * * 第二个状态：主干道亮绿灯30S、支干道亮红灯 * * 第三个状态：主干道绿灯闪3次转亮黄灯、支干道亮红灯3S * * 第四个状态：主干道亮红灯、支干道亮绿灯25S * * 第五个状态：主干道亮红灯、支干道绿灯闪3次转亮黄灯3S * * 返回到第二个状态 *- * Crossroads traffic light controller* * The fir
PILILED
- 霹雳灯 P0---8个LED和P2---8个LED 硬件：8路指示灯接P0口，或者P2口-Perak P0--- 8-LED lights and P2--- 8-LED Hardware: 8-way light then P0 port, or P2 I
HYLED
- 花样流水灯 P0---8个LED和P2---8个LED 硬件：8路指示灯接P0口，或者P2口-Synchronized flow P0--- 8-LED lights and P2--- 8-LED Hardware: 8-way light then P0 port, or P2 I
INT1
- 中断控制的P1.1小灯。采用12MHZ晶振-P1.1 interrupt control of a small lamp. 12MHZ crystal with
0804KONG
- adc0804制作的温度控制器, 设一个加热器p2.0一个制冷器p2.7 设定下限温度30度(设4bh)存31h上限温度60度(设96h)存30h 调整ad电位器可观察到p2.0,p1.4继电器端口的动作范围-93C46 way to read and write 8-channel Marquee LED display* * 0x00 starting from the address to write data " 1-8" and then read out
pc2soundcard
- 用汇编语言开发的利用电脑喇叭模拟声卡的程序源代码。-Using assembly language to develop and use a computer sound card speaker simulation program source code.
cpuid
- 汇编语言，获取CPU信息。代码中只含有部分cpu信息，可以根据自己需求增加。-Assembly language, access to CPU information. The code contains only part of the cpu information may be according to their demand.
mysht10
- SHT10-LED温湿度显示KeilC程序-SHT10-LED display temperature and humidity KeilC program
scamitic
- Check the waveform in oscillscope on different oscillator frequencies
wc
- 基于pic16f877单片机的程序编写，包括一系列的子程序-Pic16f877 microcontroller-based programming, including a series of subroutines