搜索资源列表
SERIL_COMM
- 提供一个上位机串口通信的源代码,方便开发上位机通信-Provide a host computer serial communication s source code, facilitate the development of PC communications
ScibasedVC6
- 基于VC的上位机串口通讯,可以设置波特率,数据位数,打开串口,关闭串口等,实现和DSP2812通讯,实现对电机转速和转矩的设置.-VC' s PC-based serial communication, you can set the baud rate, the median data, open the serial port, serial port, such as shut down, and realize DSP2812 communications, realize on
delphi_MSComm_image
- delphi用MSComm进行串口通讯,如果接受到的是连续的一组完整数字则将其进行图像还原。 本代码的另外一个是MSC51F310编写的单片机代码,两个合在一起完成从单片机将视频图像采集并发送到上位机还原的过程。-Comm by RS232,Program by DELPHI, link PC do F310,allow msc51f310 send a picture to PC .
11
- 本文介绍了一种基于VB的计算机串口通信,实现上位机对台达变频器的通讯及对变频器实时监控的功能。 关键词: 串行通信 变频器 VB -In this paper, a computer based on the VB serial communications, PC implementation Tatsu Taiwan inverter communications and real-time monitoring of the inverter function. Keywords
UART_SUCCESS
- 实现FPGA和上位机的串口通信,里面由波特率发生器,移位寄存器,计数器,detecter,switch,switch_bus等功能块综合而成。-FPGA implementation and the host computer' s serial communication, which by the baud rate generator, shift register, counters, detecter, switch, switch_bus such as function bl
SEND
- 51单片机通过rs232串口 向 上位机循环发送数据-51 MCU through RS232 serial bit upward cycle send data
Flash_ROM_lab
- 用SmartGen生成一个256*8的大小同步FIFO,并通过串口发送数据初始化FIFO。然后,再通过串口返回到上位机的串口调试程序显示,确认数据是否正确。-SmartGen generated with a size of 256* 8 Synchronous FIFO, and sending data through the serial port to initialize FIFO. And then back through the serial port to the PC ser
SWJ
- 串口上位机,用于接受下位机所传数据,实现双向控制,本软件是用于接受、控制,无线终端节点-PC serial port for the next bit plane data by mass, to achieve bi-directional control, the software is used to receive, control, wireless terminal nodes
VBwithOmronPLCthroughRS-232PCserialcommunicationpr
- VB与欧姆龙PLC通过RS-232串口通讯 的上位机程序-VB with Omron PLC through RS-232 PC serial communication program
123
- 磁罗盘的上位机界面,包括串口接收以及数据曲线绘制-Magnetic compass interface of the host computer, including the serial data receiver and curve drawing
16x96
- 16x96点阵串口接收带上位机仿真,挺不错的-16x96 led dot matry serial port with up machine soft
UARTc
- ARM9s3c2410的串口通讯实验,通过上位机与下位机的串口实现键盘按键能在dnw上显示出来。-Serial Communication ARM9s3c2410 experiments, through the host computer and the next crew to achieve the serial keyboard keys can be displayed in dnw.
c8051f020_temp
- c8051F020片内温度测量,通过串口发送到上位机-c8051F020-chip temperature measurement, through the serial port is sent to the host computer
my_uart_top
- 实现的功能如题,就是FPGA里实现从PC接收数据,然后把接收到的数据发回去。使用的是串口UART协议进行收发数据。上位机用的是老得掉牙的串口调试助手-To achieve the functions such as title, that is, to achieve FPGA receives data from the PC, and then receive data back fat. Using a UART serial port protocol to send and recei
AI_Bus_70
- 厦门智能仪表通讯协议 宇电协议 给有需要串口编程的人帮助-yudian xieyi
freescale
- 此源程序为freescale智能车竞赛上位机程序,实现对cmos摄像头采集的数据通过串口传到pc机,然后还原赛道信息,以及这种的曲线显示和数据分析-This source code for the smart car competition freescale PC program to achieve cmos camera on the data collected through the serial port pc spread, and then restore the track,
danpanjicangyongcx
- 这个包中提供了一些有实际应用价值的子程序供参考选用 SUB1----X25045/43 看门狗/存储器与 89C2051接口子程序 源程序/原理图(21K)X25045.EXE SUB2----AT24C02/04/08/16 串行存储器与 89C2051接口子程序 源程序/原理图(22K) AT24C02.EXE SUB3----红外遥控器(熊猫M50462/C54L2)与 89C2051接口子程序 源程序/原理图(21K)
51Serial
- 51单片机的串口编程,利用Proteuse仿真通过,可以用虚拟串口软件设置好,在上位机上查看。-51 single-chip serial port programming, through the use of Proteuse simulation can be used to set up a virtual serial port software in the host computer to view.
receive
- 基于msp430单片机的rf905无线接受源代码,+上位机串口通讯-Msp430 microcontroller-based wireless rf905 accept source code,+ host computer serial port communication
code
- 单片机步进电机控制系统,AT89C51控制2个步进电机,通过串口有上位机控制转向和角度。-Microcontroller stepper motor control system, AT89C51 control two stepper motors through the serial port with upper motor control steering and angle.