搜索资源列表
Android蓝牙串口助手亲测可用
- Android蓝牙串口助手亲测可用，买的别人的代码，android蓝牙上位机，用于接收单片机串口发送的数据
kehshechenxu
- 编制一全双工UART电路，通过试验箱MAX202E转换成RS232电平，与计算机进行通讯实验，设置8个按键，按键值为ASIC码“1”~“8”，通过串口发送给计算机，在计算机上显示键值，同时在数码管最高位显示；计算机可发送“0”~“F”的ASIC码，FPGA接收后在数码管低位显示0~F。通过按键可设置波特率。 要求：波特率为三种 1200、2400、9600，由1个按键选择，3个LED分别指示； 数据格式为1位起始位、8位数据位和一位停止位； 上位计算机发送接收软件可使用
03-多路ADC转换-模拟串口发送
- 在stc51单片机上实现对多路ADC、串口的控制例程(Stc51 MCU in the realization of multi-channel ADC, serial control routines)
IIC读写EEPROM发送到PC串口
- 能实现用IIC读EEPROM并且将读取的数据通过串口发送到PC端，以及在PC端通过串口发送数据给FPGA，再利用IIC将数据写入EEPROM(The program can realize that FPGA read the data from EEPROM by IIC and then send it to PC by UART,and that PC send the data to FPGA by UART and then write the data to EEPROM by
ComTest
- 串口通信，实现串口发送，接收，并统计相应数据，可对波特率，COM端口进行配置(Serial communication, serial port to send, receive, and statistics corresponding data, baud rate, COM port configuration)
stc15w408as
- 利用stc15管脚切换的方式，实现双串口通信(The double serial communication is realized by the way of stc15 pin switching)
VC向指定串口发送和接收数据（可十六进制）
- VC++ 串口通信，很不错的，感谢大家的支持与下载(VC++ serial communication, very good)
串口通讯
- 用于单片机与PC之间的通讯，发送与接收字符，执行相应的指令(communication between PC and SCM)
C8051F020实现ADC采样芯片外
- C8051F020实现ADC采样芯片外的模拟电压，通过LCD显示，并通过串口发送到PC机(C8051F020 analog chip to achieve analog voltage outside the ADC, through the LCD display, and sent to the PC through the serial port. Required Downloads)
sound_wave
- 使用串口定时器发送1038字节的数据.,可以通过串口助手接收数据(Use serial timers to send 1038 bytes of data)
C#直流电机pid调速
- 用C#编写的串口调试软件，下位机在STM32上测试通过，下位机发送数据的格式如printf("%s%f%s%f%s",":"x1":"x2":")单片机串口发送数据(Written in C# serial debugging software, the lower computer on the STM32 test passed, the lower machine to send data format, su
AutoUpdate
- MFC通过HTTP下载文件并通过串口发送到linux话机(MFC downloads files via HTTP and sends them to the Linux phone via a serial port)
UART发送接收
- stm8串口与上位机进行通信，上位机先发送数据给单片机，单片机再将数据反馈给上位机(Stm8 serial communication with the host computer through the computer, sends the data to the MCU, MCU and data feedback to the host computer)
等精度数字频率计
- 可以测量1HZ-150MHZ矩形波(其他波形需整形后输入)信号，误差<0.01%，串口输出NC和NX值。(1HZ-150MHZ square wave can be measured (other waveform needs to be shaped after the input) signal, error <0.01%, serial output NC and NX values.)
9、CC2530 串口UART0发送字符串
- cc2530程序基于IAR开发环境,实现串口发送字符。(CC2530 program, based on the IAR development environment, serial transmission characters.)
uart
- 实现串口发送和接收功能，数据处理模块可自行修改。(Serial port to send and receive functions, data processing module can modify its own.)
测试
- 上位机通过串口发送相应命令控制设备并将设备当前状态返回给上位机(The upper computer sends the corresponding command control device through the serial port and returns the current state of the device to the host computer)
serial port write
- 使用labview编写的串口发送小程序，实现上位机与下位机串口通信(Using LabVIEW to write the serial port to send small programs to achieve the upper computer and the lower computer serial communication)
Tx_async
- 串口发送文件，实际测试过，功能可以实现，信号已经标注(Serial send files, the actual test, the function can be achieved, the signal has been marked)
串口2.0
- 两台电脑进行文件数据传输与接收，一台在传输口里输入数据，点击发送后，另一台可以接收到(Data transmission and reception between two computers)