搜索资源列表
MDK-bill-develop
- STM32F407Ddiscovery实现串口打印和点亮LED功能-STM32F407Ddiscovery achieve serial print and light LED function
6050
- 这篇源码基于模拟MSP430F5438型号的6050程序直接通过串口打印相应的数据已经做完四元数解算-This source is based on the simulation of the MSP430F5438 model 6050 procedures directly through the serial print the corresponding data has been completed four yuan solution
Com
- 读串口工具，重复的数据只打印一次-Read a serial port tools, duplicate data print only once。。。。。
PrintTest
- MFC 开发的打印源码，可以连接斑马打印机等其它打印机，支持 串口 和 LPT并口 打印两种方式，网上资源实在太少，得之不易，于是分享给大家- MFC 开发的打印源码，可以连接斑马打印机等其它打印机，支持 串口 和 LPT并口 打印两种方式，网上资源实在太少，得之不易，于是分享给大家 Print source MFC development, can be connected to other Zebra printer printer, support serial and LP
stm32f0-chip-unique-ID
- 本文件实现的功能是获取stm32f0芯片的唯一ID，并通过串口打印。-Get stm32f0 chip unique ID, and print through the serial port
colloction
- Arduino串口通讯，发送1开始采集，对A0-A4口轮询采集，并打印出来，每一路数据分别以a,b,c,d,e标识,适合新手-Arduino serial communication, send 1 to start collection, the A0-A4 port polling collection, and print out, each way the data were a, b, c, d, e logo
K60_DMA_Eagle-eye-camera-capture
- K60单片机通过DMA方式获取鹰眼摄像机数据，然后通过串口在上位机上打印输出-K60 microcontroller through the DMA way to obtain eagle eye camera data, and then print the output on the PC through the serial port
suceed
- 基于STM32的ADXL345三轴加速度传感器程序，可以通过串口将数据输入电脑并打印-STM32-based ADXL345 three-axis acceleration sensor program, you can enter the data through the serial port and print
PC机 采用主从方式 采集总线上的多块MINI板
- 主从方式，主机通过CAN读取从机的单片机温度数据，主机收到的数据在PC端串口助手显示。 单片机stm32f103c8t6(Master/Slave Master read temper data from Slave through Can-bus. The temperature data Master received will print to PC through UART&USB transmitter. MCU is stm32f103c8t6.)
ADC-DMA
- 连续采集AD转换值，使用DMA的方式保存，并使用串口将AD转换结果打印(Continuous collection of AD conversion value, using the DMA way to save, and use the serial port to print the AD conversion results)
单片机AD
- 使用单片机内部Ad，实现单片机AD十位采集数据，并且通过串口打印出来。可以啦，就这么简单(The use of single-chip internal Ad, to achieve single-chip AD ten bit data acquisition, and print through the serial port. Yes, it's that simple)
uart
- 在zigbee的裸机下，用IAR实现串口打印(To achieve serial print)
STM32printf
- 这是一个在stm32上运行的Printf打印功能函数，它可用于串口调试打印一些调试信息，帮助分析问题。(This is a Printf print function that runs on the STM32. It can be used for serial debugging, printing some debugging information, and helping to analyze problems.)
C—program
- 读取标准卡 并在串口打印符合要求的标准卡卡号，同时有其它一些未启用的功能，需要的可以酌情添加。(Read the standard card and print in line with the required standard card number, and some other functions are not enabled, you can add as appropriate.)
stc15测脉宽
- 采用stc15单片的捕获功能测量脉冲周期 精度高 误差小 将测量结果打印到串口显示结果(Stc15 capture function is used to measure the pulse cycle, high accuracy, small error, and print the measurement results to the serial port)
826611100
- esp8266 tcp网络串口助手发数据，接受同时打印在网络串口助手和串口助手上(Esp8266 TCP network serial assistant to send data, accept, print at the network serial assistant and serial assistant)
adc
- 采集三路ADC信号，转化后串口1打印输出(Acquisition of three ADC signal, the conversion of the serial port 1 print output)
ds1302
- 实现实时时钟，读取ds1302的值，并将其转化为一般的时间格式，串口打印输出。(To achieve real-time clock, read the value of DS1302, and convert it into a general time format, serial print output.)
nrf24l01
- 采集16个单片机I/O口电平通过nrf24l01发送 在接收端通过串口打印出来(Acquisition of 16 single-chip microcomputer, I/O port level through the nRF24L01 send, in the receiving end through the serial port print out)
inputtest
- 本实验利用TIM5_CH1来做输入捕获，我们将捕获PA0上的高电平脉宽，并将脉宽时间通过串口打印出来，大家可以通过按WK_UP按键，模拟输入高电平。同时，本实验将保留上一个实验的PWM输出，DS0还是会由暗-->亮的循环变化，大家可以通过杜邦线连接PA0和PB5，来观测PWM输出的高电平时间。(This experiment uses TIM5_CH1 to do input capture, we will capture the PA0 high level pulse width,