搜索资源列表
VHDL语言的UART串行接口芯片设计程序清
- Uart 程序,用VHDL语言编写。
三种16位整数运算器的ALU设计方法
- 三种16位整数运算器的ALU设计方法,调用库函数74181(4位ALU),组成串行16位运算器。(用74181的正逻辑) B.调用库函数74181和74182,组成提前进位16位运算器。(用74181的正逻辑) 注意:调74181库设计,加进位是“0”有效,减借位是“1”有效,所以最高位进位或借位标志寄存器要统一调整到高有效 C.用always @,case方式描述16位运算器。,Three 16-bit integer arithmetic logic unit of the ALU
SPIBusVerilog.rar
- SPI串行总线接口的Verilog实现,详细讲解实现过程。,SPI serial bus interface Verilog realization elaborate on the realization of the process.
parell_to_serial.rar
- 该模块主要完成并串转换功能。其中system_clk是输入并行时钟的频率,它是串行时钟serial_clk的八倍。byte_data_en是输入并行数据使能信号,byte_data是输入并行数据。serial_data是转换后的串行数据,bit_data_enable是串行数据有效信号。,The module main is completed and the string conversion functions. System_clk which is an input parallel c
liuVHDL.rar
- 一种基于状态机设计的串并行转换电路,将LTC1196(ADC)的串行输出数据转换成并行数据的转换电路, ADC的时钟由转换电路提供,,Design a state machine based on parallel conversion circuit of the series will be LTC1196 (ADC) output of the serial data into parallel data conversion circuit, ADC clock provided by
hh.rar
- 串行输入并行输出 用vhdl语言描述的 有源代码主打色,Serial input parallel output using vhdl language to describe the main color of the source code
FPGAFFT.rar
- FPGA控制串行AD(AD0804),状态机实现,可以根据该程序实现数字电压计,数字温度计的设计,FPGA serial control AD (AD0804), state machine to achieve, you can program according to the number of voltage, the digital thermometer design
用VHDL语言将并行的8位数据换成串行输出
- 用VHDL语言将并行的8位数据换成串行输出-The parallel 8 is the data replaced with the serial output
chuanbingvhdl
- 由于计算机中大部分器件使用的是串行,本程序实现了数字电路中常用的串行输入并行输出的功能。-Because most of the computer using a serial device, the program realization of digital circuits used in serial input parallel output function.
VHDL
- 采用VHDL语言设计一个4通道的数据采集控制模块。系统的功能描述如下: 1.系统主时钟为100 MHz。 2.数据为16位-数据线上连续2次00FF后数据传输开始。 3.系统内部总线宽度为8位。 4.共有4个通道(ch1、ch2、ch3、ch4),每个通道配备100 Bytes的RAM,当存满数据后停止数据采集并且相应通道的状态位产生报警信号。 5.数据分为8位串行输出,输出时钟由外部数据读取电路给出。 6.具备显示模块驱动功能。由SEL信号设置显示的通道,DISPLAY
top
- RS232串行通信,采用VHDL编程,由波特率发生器,接收器和发送器构成-RS232 serial communication using VHDL programming, by the baud rate generator, receiver and transmitter constitute
liuVHDL
- 一种基于状态机设计的串并行转换电路,将LTC1196(ADC)的串行输出数据转换成并行数据的转换电路, ADC的时钟由转换电路提供,-Design a state machine based on parallel conversion circuit of the series will be LTC1196 (ADC) output of the serial data into parallel data conversion circuit, ADC clock provided by
Multiplier
- 用VHDL语言描述的几个乘法器实例,如串行阵列乘法器等-VHDL language used to describe a few examples of multipliers, such as array multipliers, such as serial
ad7980
- DSP并行读取串行接口A/D芯片的VHDL接口程序-VHDL Interface Program between DSP (parrel interface) and AD7980 (Serial interface)
shiftregister_32
- 长度为8的32bit串入并出移位寄存器,它的功能就是对32bit的并行信号作串行输入,并行输出处理-Length of 8 for 32bit serial in parallel out shift register
digitalock
- 数字密码锁。能实现8位串行输入,可以改密码,并能实现报警功能。-Digital code lock. To achieve 8-bit serial input, you can change passwords, and to achieve the alarm.
PULSE
- 这是一个将6组并行数据串行输出的VHDL源码,配合外部电路可以输出正负脉冲,还附有逻辑图哦。-This is a group of parallel data to serial output 6 of the VHDL source code, with the external circuit can output positive and negative pulses, also with a logic diagram oh.
piso8
- 并/串转换的VHDL源代码,其中包括完整的QUARTUS2工程,还有正确的仿真波形。串行,并行数据 -Serial/parallel conversion ,VHDL source code, including complete QUARTUS2 project, and the correct simulation waveform file.
VHDL
- 序列检测器设计VHDL源程序 任意输入串行数据串-VHDL source code sequence detector design arbitrary string of serial data input
serial_adder
- 串行加法器的vhdl描述,用两个移位寄存器和一个全加器,一个d触发器实现(The VHDL descr iption of the serial adder, with two shift registers and a full adder, a D trigger)