搜索资源列表
STC15F204EAPNTE
- 本系统采用STC15F204EA单片机+10kNTC热敏电阻组成测温系统,4位共阳数码管显示温度,如需要电路资料可以联系我-The system uses STC15F204EA microcontroller+10kNTC thermistor composed of a temperature measurement system, the four common anode LED display temperature, such as circuit information you c
VVHDL_32bit_tH
- VHDL写的32位计数，两个四位共阳数码管输出串口输出+数码码管显示的计时器程序每次停止后串口输出。，已通过测试。 -VHDL written 32 count, two four sun digital serial output tube output serial output the+ digital code to display the timer program each stop. , Has been tested.
LED
- DSP的SPI工作原理DSP，CPLD，74HC595（串入并出的移位器），共阳数码管。SPIMOSI和 SPICLK直接从DSPJIE接到了74HC595的SER和SRCLK，作为数据和时钟信 号的输入，SPICS由CPLD引出来控制74HC595的选通。-DSP SPI works DSP, the CPLD, 74HC595 (string in and out of the shifter), Yang digital tube. The SPICLK SPIMOSI and d
51
- 超声波测距 /晶振=8M //MCU=STC10F04XE //P0.0-P0.6共阳数码管引脚 //Trig = P1^0 //Echo = P3^2-the the compass/crystal = 8M// MCU = STC10F04XE// P0.0-P0.6 common anode digital control pin// Trig = P1 ^ 0// the Echo = P3 ^ 2
Infrared-obstacle-avoidance
- 通过2路红外发射，顺序接收，检测收发功能是否正常用手遮挡对应的发射管，用共阳数码管的a、d端模拟左右2端每60ms分别检测2路发射，通过每组发射10个脉冲，如果接收到的脉冲个数大于6，表明有遮挡存在-Order to receive through the 2-way infrared emission detection transceiver functions are normal hand blocked the launch tube, common anode digital tub
8weidanguandisplay
- 8位共阳数码管单管显示，protues仿真+c语言源代码-8 common anode digital display tube single tube, protues simulation+c language source code
Timer
- 基于8寸共阳数码管的数字时钟，带有DS18B20温度检测+环边秒流水灯-Based on the 8-inch common anode digital tube digital clock with the DS18B20 temperature detector the+ ring side sec light water
double-Infrared-test
- 通过2路红外发射，顺序接收，检测收发功能是否正常,用手遮挡对应的发射管，用共阳数码管的a、d端模拟左右2端,每60ms分别检测2路发射，通过每组发射10个脉冲，如果接收到的脉冲个数大于6，表明有遮挡存在-Order to receive 2-way infrared emission detection transceiver function is normal, hand block the corresponding launch tube, pipe a common anode dig
M81629A
- ATNEGA8 TM1629A驱动16位共阳数码管 阴码转阳码 -ATNEGA8 TM1629A drive 16 common anode the digital tube overcast code positive the code
ourdev_599970AZGFDT
- 一个icl7107的proteus仿真电路，内含4个共阳数码管。-A icl7107 proteus simulation circuit, containing a total of four digital seg.
STC12C5A60S2
- STC12C5A60S2程序2013.1.15共阳数码管-STC12C5A60S2 program 2013.1.15 common anode digital tube
Total-digital-HJ-C52
- 基于51单片机的共阳数码管显示实验c代码-Based on 51 single-chip digital display common anode experiment c code
Two-separate-button-digital-counter
- // 独立2按键控制2位LED共阳数码管计数器 // // 个位数码管接在P0端口； // 十位数码管接在P2端口； -//Buttons control two independent two common anode LED digital tube counter//// bit digital tube connected to the P0 port // ten digital tube connected to port P2 //
ex63
- 四位共阳数码管快速扫描显示1,2,3,4-Four common anode LED display 1,2,3,4 quick scan
juzhenjianpan
- MSP430F169单片机矩阵键盘扫描程序，用一位共阳数码管显示-MSP430F169 microcontroller matrix keyboard scanning procedures, using a common anode LED display
WEN-DU-JI
- 利用单片机AD功能和热敏电阻测温，三位共阳数码管显示-AD using SCM functions and thermistor temperature measurement, three were positive digital display
main
- 1：读取输入P1.0口的电压值，由于硬件实现了将5V以上的电压转换为三分之一的输入定呀， 由于电动车单个蓄电池最高电压为12v，经过运放电路，输入到P1.0口的电压值最高是4V 2：当读取到的电压小于3V，声光报警电路接通并报警。 3：P1.3口具有高低捕获功能，本程序设定是下降沿触发。 将捕获到的数字经过转换后送到数码管显示。 4：数码管是4位带小数点共阳数码管。用于显示转速大小。转速单位是Km/h。 一般电动车最高时速不超过100K
LED
- C51单片机共阳数码管显示变化数字实验例程-C51 single-chip digital display of positive changes in the digital test routines
SMG138
- 74HC138驱动数码管程序，驱动4位共阳数码管，阳极全部高电平，138驱动段码-74HC138-driven digital control program
danpianjishiyan
- 单片机实验 一、实验内容 1、静态显示一位数码管（本实验为共阳数码管） 2、利用实验箱提供的显示电路,动态显示一行数据（12345678）. 二、实验目的 1. 掌握数码管的静态与动态显示。 2. 了解用总线方式控制数 -#include<reg51.h> #define T 100 void delay(int ys) { int i,j for(i=ys i>0 i--) for(j=110