搜索资源列表
serial-port-test-program
- MSP430单片机串口测试程序。该程序将串口收到的字节发回主机,供测试串口用。用串口调试助手向430发送任意字符串,将接收到同样的字符串.也可用Windows自带的超级终端,设置波特率2400,8位数据,无校验无流量控制,连接。计算机键盘上按任意字母,屏幕会有回显。-This is a serial port test program on MSP430 MCU.
send
- 使用《窜口调试助手》软件,16进制显示。 窜口波特率:9600? 校验位:NONE 数据位:8 停止位:1 学习简单的从单片机往PC发送数据 每按下一次按键KEY3,窜口调试助手显示数字"62"-Use the " channeling port debugging assistant" software, 16-band display. Channeling port baud rate: 9600? Parity
3
- 单片机通过串行口发送数组(十六进制,可改),可经MAX232电平转换,PC机串口接收,程序实测,可改,请注意波特率和晶振的选择-Microcontroller through the serial port to send the array (hex, can be changed), via MAX232 level translator, PC serial port to receive, process measurement, can be changed, please note
labview
- 赛道图像显示系统 程序功能:通过串口通讯显示单片机采集的赛道二值化图像40*10 数据格式:先通过串口发送起始识别字符,本程序定义为car,再发送40*10的图像数据,1为黑,0为白 说 明:1.开发环境为NI公司的LABVIEW8.5 2.开发软件需要安装串口插件VISA方可正常使用 3.默认通讯波特率为115200 4.起始识别为3个字符car,默认图像分辨率为40*10,可根据需要自行修改 5.串口读取缓冲区大小应设定为2*(起始设别字符+图
practice32
- //以16进制发送一个0-65536之间的任一数,当单片机收到后在数码管上动态显示出来,波特率2400 -//Send a 16-hexadecimal any number between 0-65536, when the microcontroller in the digital receipt is displayed on a dynamic, baud rate 2400
Main
- 51单片机的串口通信程序,采用中断的方式,波特率为96-51 microcontroller serial communication program, using interrupts the way, the baud rate of 9600
C8051F30x
- C8051F30x的UART方式的BOOTLOADER上位机程序原代码,包含使用说明及C8051F310单片机与计算机的串口通信的例程, 串口发送,波特率1152-C8051F30x the UART mode BOOTLOADER PC program source code, including instructions and the C8051F310 microcontroller serial communication with the computer routines, ser
CAN
- PIC单片机CAN通讯例程,包括CAN通讯初始化,波特率计算等。-PIC microcontroller CAN communication routines, including the CAN communication initialization, baud rate calculation.
danpianji
- 利用单片机实现双机串口通讯,波特率可调。通讯的内容为 采集温度传感器的信号,并要求丛集能够将温度及波特率显示出来。-dan pian ji
ir
- 单片机红外串口通信程序,波特率1200.cd4011起振,通信距离5米。还有原理图-Single-chip infrared serial communication program, the baud rate 1200.cd4011 start-up, communication distance of 5 meters. There schematic
RS_232
- VHDL实现RS232串口通信,压缩包内有完整的quartus2工程,由顶层,波特率,发送,接收四个模块构成。外部电路只需要一片MAX232就能与串口助手或单片机通信。-VHDL implementation of RS232 serial communication, compressed within a complete quartus2 project from the top, baud rate, send, receive four modules. External circui
simulate
- 51单片机,引脚模拟波特率9600的串口-51 pin simulate serial port
3
- 要求C语言编写,实现C8051F020通过UART于PC实现数据交换,单片机使用外部22.1184MHz晶振。要求实现的功能:Uart驱动程序,包括初始化、波特率设置,单字节发送接收、字符串发送接受。 程序运行时向PC机发送字符串;接收到PC机的数据后,再将该数据发送回PC机。-Requirements written in C, to achieve C8051F020 UART to PC through data exchange, the microcontroller using an
USART
- atmega16单片机串口调试程序,波特率设置很方便-atmega16 chip serial debugging process, it is convenient to set the baud rate
modbus-PCPdouble--SLAVE
- STC1C5204AD单片机modbus多机通信程序,一台PC带两台从机,其中一台晶振为11.0592M,另一台为12M,采用通信波特率为19200bps,实现了标准modbus的3和6命令,采用485通信协议,4854使能端为P3.7-STC1C5204AD microcontroller modbus multi-machine communication program, a PC with two slaves, one of the crystal is 11.0592M, anoth
serial_send_receive
- 51单片机串口通信程序。有初始化,收发函数,波特率9600.-1602 LCD program, notes complete.
rs232
- 单片机串口通信,连接好串口或者usb转串口至电脑,下载该程序,打开电源 打开串口调试程序,将波特率设置为9600,无奇偶校验 晶振11.0592MHz,发送和接收使用的格式相同,如都使用 字符型格式,在发送框输入 hello,I Love MCU ,在接 收框中同样可以看到相同字符,说明设置和通信正确-Connect the serial port or usb to serial port to your computer, download the program,
danpianji
- 单片机小精灵是单片机的串口波特率计算用的-Single-chip microcontroller elf serial port baud rate is calculated using
51_DHT21
- DHT21使用范例 //单片机 : AT89S52 或 STC89C52RC // 功能 :串口发送温湿度数据 晶振 11.0592M 波特率 9600 //硬件连接: P2.0口为通讯口连接DHT11,DHT11的电源和地连接单片机的电源和地,单片机串口加MAX232连接电脑 -DHT21 use examples //SCM: AT89S52 devices or STC89C52RC //function: serial send temperat
51_asm_DHT21.asm
- DHT21使用范例 单片机 : AT89S52或 STC89C52RC 功能 ; 串口发送温湿度数据 波特率 9600 -DHT21 use examples AT89S52 SCM: or STC89C52RC Function Serial send temperature and humidity data baud rate 9600