搜索资源列表
stm8S003LCD
- 自己编的用单片机驱动段式液晶程序,用的轻型电动车上显示电量和速度等-Own MCU segment LCD driver program, with light electric vehicles display power and speed
STEP-MOTOR
- 步进电机传动可调节速度包含延时程序主要用于51单片机的步进电机控制,是比较基础的程序。很适合入门者-Speed of step motor drive
adxl345
- 计步器,基于单片机与ADXL三轴加速度传感器的计步器,实现计步、1602显示步数及平均速度功能。 - Pedometer, pedometer-based SCM and ADXL triaxial accelerometer achieve pedometer, 1602 show the number of steps and the average speed function.
wbljr
- 51单片机作为核心控制,控制步进电机的速度,进行加热-51 microcontroller as the core control, stepper motor speed control, heated
motor_pwm
- 基于51单片机的PWM电机速度调制程序设计,速度滤波算法控制。-51 microcontroller PWM motor speed modulation procedures based on the speed control filtering algorithm.
car
- 履带小车循迹避障测速,使用51单片机,利用红外线传感器检测地面上的黑带,沿着黑带移动,通过记录转速和时间计算速度。包含超声波测距用于避障-The pedrail dolly tracking obstacle avoidance velocity, using 51 single chip, using infrared sensors to detect the ground of black belt, moving along the black belt, by recording th
MPU9250-use-SPI-config-AK8963
- MPU9250 9轴传感器,使用SPI4线模式,配置9轴数据,包括AK8963磁力计。相比I2C模式下的400K/S spi模式具有更高的传输速度。(使用的是STM32单片机)-MPU9250 9-axis sensor using SPI 4-wire mode, 9-axis configuration data, including AK8963 magnetometer. 400K/S compared to I2C mode spi mode has a higher tran
GPS
- 用C51单片机接受GPS信号,并通过12864显示,显示经度,纬度,时间,速度- C51 MCU with the GPS signal, and through the 12864 display, showing the longitude, latitude, time, speed
12864lcd
- 基于51单片机的12864显示骑单车里程,时间,速度,卡路里。-51 microcontroller-based display 12864 cyclists mileage, time, speed, calories.
PWM
- PWM电机无极调速,用PWM控制直流电机的转动速度,基于51单片机,C语言-PWM motor stepless speed control, the PWM control the rotational speed of the DC motor, based on 51 microcontroller, C language
ALIENTEK-MINISTM32-GPSNEO-6M-
- GPS模块的信息读取,解析。通过UART接口和单片机直接通信。能够知道经纬度、速度、高度、时间等信息。-Read the information of GPS module, parsing.Through the UART interface and the single chip microcomputer communication directly.To know the information such as latitude and longitude, speed, height
SCMFanSpeedControl
- 利用单片机控制小风扇速度(PWM方式),效果还不错,采用keil软件编程-Using single-chip microcomputer to control the speed of the fan (PWM mode), the effect is good, using keil software programming
7.5PID
- 使用单片机K60,欧姆龙编码器,进行PID调速,电机速度快速稳定-Using SCM K60, OMRON encoder, PID speed, motor speed stability
tcpip
- 基于TCP/IP通讯的仪器仪表应用层协议架构由于新一代仪器仪表的数据量大,传输距离远,实时性高,传统的基于RS232/RS485的串行数据传送方式已不能满足要求,而基于TCP/IP的以太网数据通讯方式,传输距离大(通过internet,理论上无限远),速度快,是当前新一代仪器仪表数据传输的理想方式。 基于单片机(如MCS51+RTL8019AS)的以太网接入技术已经相当成熟,可以方便的与PC机连接。根据仪器仪表嵌入式应用的要求(如实时性),我们采用TCP协议或UDP协议进行数据传输。TCP是
test
- 利用51单片机控制无刷电机转速 通过按键和蓝牙控制 分为三挡速度-Brushless motor speed control by 51 single-chip and Bluetooth control buttons and speed into the third gear
8-Channel-TDS
- 优化如下: 1、结合论坛大家的程序,去粗取精。 2、大家的程序都是在单片机开一个128bit数组,存储显示数据,一方面占用了单片机的宝贵空间,而且,每次改变一个段位,都要把全部数据写一遍,比较占用时间。 3、采用对所写段位先读后写的方式,每次只读写4bit,对数字位,只读写8bit,提高速度。 4、程序在89s52单片机运行通过,程序中加了详细注解,便于阅读。 5、编译后的空间占用由论坛的程序的1200字节降到800字节,降低1/3.-Optimization is
lwIP-1.4.0
- lwip1.4源码,纯净版代码,能够在单片机上实现网络通讯,最大传输速度100Mbit-Lwip1.4 source code, pure version of the code, to achieve single-chip network communications, the maximum transmission speed 100Mbit
51
- 基于51单片机的步进电机的控制,可以实现速度控制,数码管显示,变向开关-51 MCU control stepper motor-based, you can achieve speed control, digital display, switch to change
OpenLoopSenBLDC.X
- dsPIC30F4011单片机控制无刷直流马达无霍尔感应器程序并实现速度环调速-DsPIC30F4011 single-chip control of brushless DC motor without Hall sensor program and achieve speed loop speed
ClosedLoopSenBLDC.X
- dsPIC30F4011单片机控制无刷直流马达有霍尔感应器程序并实现速度环调速-dsPIC30F4011 microprocessor controlled brushless DC motor has a Hall sensor program and achieve the speed loop speed