搜索资源列表
tax1
- 1、 设计一个出租车自动计费器,具有行车里程计费、等候时间计费、及起价三部分,用四位数码管显示总金额,最大值为99。99元;-one, design a taxi for automatic billing, with mileage billing, the waiting time billing, and three starts, with four Digital Display total amount of the maximum 99. 99;
51asn
- 设计的温度采集模块是应用一个滑动变阻器通过改变电阻值进行模拟的温度值改变情况;模数转换模块是运用ADC0809芯片进行模数的转换,把采集到的模拟电压值变为数字值;单片机控制系统通过程序判断此数字值的大小,这样控制温度报警模块,一方面控制发光二极管的亮灭情况,另一方面控制蜂鸣器的报警;温度显示模块应用四位数码管显示模拟的温度值。因此,构成了此模拟的温度控制系统。本系统主要实现了模拟的温度值在30到60的一个设定范围内,正常显示温度,一旦超过了此范围,就会有报警。-design of the tem
20068211814414818
- 设计十一 出租车自动计费器 1、 设计一个出租车自动计费器,具有行车里程计费、等候时间计费、及起价三部分,用四位数码管显示总金额,最大值为99。99元 -11 taxi design for an automatic billing, automatic design of a taxi meter, with traffic milestone billing, waiting time billing, and From three parts, with four LED show
dong0
- 可实现双通道ad转换 四位数码管动态扫描-can achieve double-channel digital ad conversion of four dynamic scan
0000dao9999.asm
- 采用8051单片机驱动四位数码管的定时器系统。采用keil编译-used 8051 four-driven digital control timer system. Compiled using keil
9999counter
- 四位数码管计数9999倒计数程序,测试用,供初学者参考
TIME.C
- 用四位数码管显示时间源程序 用四位数码管显示时间源程序
TIME1.C
- 用四位数码管显示时间源程序1
8052
- *本程序四位数码管作倒计时.P0为位选,P1数码管.P3.5输出(低电平).P3.0,P3.1串口通讯.
AE182-DS18B20
- 温度显示用四位数码管,当温度>=100度时,第四位开始显示。 第五位数码管显示状态符号。 开机检测 DS18B20 状态: DS18B20正常显示: O 18.8 ← 显示实时温度和加热标记“O” DS18B20不正常显示: 黑屏、蜂鸣器一直响。
DTXS
- Verilog HDL编写的四位数码管动态显示程序,外围电路用CPLD来实现
dianji.rar
- 步进电机控制 设计硬件电路和单片机程序,实现对四相步进电机的运动控制,包括正反向的速度控制和角度控制。 STC89C51、四位数码管、步进电机、ULN2003,Stepper motor control circuit and single-chip hardware design process, to achieve four-phase stepper motor motion control, including the pros and cons to the speed contr
MEGA8
- ICC mega8例子,包括时钟,音乐,中断,PWM波,四位数码管-ICC mega8 examples, including the clock, music, interrupt, PWM wave, the four digital tube, etc.
5502
- 实用电子钟,为六位数码管时钟程序直接使用,p3.2,p3.3,p3.4,p3.5 四键控制!实测24小时误差5秒。-Practical electronic clock, nixie tube clock for the six programs used directly, p3.2, p3.3, p3.4, p3.5 four key control! Measured 24-hour error of 5 seconds.
MCU-_chengxu-
- 一个51 单片机程序步进电机控制 设计硬件电路和单片机程序,实现对四相步进电机的运动控制,包括正反向的速度控制和角度控制。 STC89C51、四位数码管、步进电机、ULN2003-A stepper motor control 51 single-chip program designed hardware and SCM process, to achieve the four-phase stepper motor motion control, including forward and
chengxu
- 实现函数信号频率的测量与显示,用四位共阳极数码管,基于单片机89C51(Measurement and display of signal frequency)
9-定时器0动态显示数码管
- 在8M晶振下,实现四位数码管利用定时器0定时动态显示(Under the 8M crystal oscillator four bit digital tube is implemented)
tian4
- 四位八管数码管每一秒增一,共阴极,可增大到9999(The digital tube increases every second.)
2061-六位数码管频率计
- 本数字频率计将采用定时、计数的方法测量频率,采用一个四位共阴极数码管显示器动态显示6位数。测量范围从1Hz—400kHz的方波、 用单片机实现自动测量功能。 基本设计原理是直接用十进制数字显示被测信号频率的一种测量装置。它以测量周期的方法对正弦波、方波、三角波的频率进行自动的测量。
TM1650四位共阴数码管模块配套资料
- TM1650芯片驱动四位共阴数码管。即模块配套资料。(Supporting data of tm1650 four digit common cathode nixie tube module.)