搜索资源列表
main
- 写命令到CH37505U盘创建写TXT向USB主机端点的输出缓冲区或者USB 端点2的上传缓冲区写入数据块。首先写入的输入 数据是数据块长度,也就是后续数据流的字节数。数据块长度的有效值是0 至64,如果长度不为0,则单片机必须将后续数据逐个写入CH375-write data_to usb
signal-analyser
- 使用msp430f2618,整形电路以及峰值检测电路做的信号分析仪,能实现测频,测峰值以及测有效值功能!整个工程都上传了(IAR环境)-Use msp430f2618, plastic circuit and peak detection circuit do signal analyzer, can realize frequency measurement, the peak and the effective value function!
bishe
- 该程序用于测电网的交流电压有效值,最后的结果将在4个LED上显示,保留1位小数-The procedures used to measure the AC rms voltage of the grid, the final result will be displayed on the four LED to retain a decimal
02-NEC_1999_B
- 数字有效值电压表(1999年B题),本例程的rst(复位)键位于拨码开关的第1位(最右边),高电平有效。-Digital rms voltmeter Problem B (1999), the routine rst (reset) button is located in one of the DIP switch (far right), active high.
time
- 该程序对信号进行时域分析,包括求有效值,画时域图形等-The program is the signal time-domain analysis, including seeking the valid values for paintings domain graphics
ss
- AD637将交流电压转换成有效值,并用ADC0804和STC89C52将有效值采集后显示在12864上-AD637 will convert the AC voltage RMS, and displayed in the 12864 on the ADC0804, and STC89C52 Valid values collected
main
- 基于msp430的数据采集还有12864液晶显示程序。还有数据处理计算有效值。-Display program based on the msp430 the data acquisition 12864. There are data processing to calculate the RMS.
AC_ModulePFreq
- 基于LM3S9B92开发板AD模块实现交流小信号有效值的测量并能同时测量频率-RMS measurement of AC small signal and capable of simultaneously measuring the frequency based the LM3S9B92 boards AD module
AC_Test
- STC12单片机定时器测定交流有效值,软件计算-The STC12 MCU Timer Determination AC RMS, the software calculates the
dian-ya-biao-yiqiande
- 通过采样PA0(ADC_0)引脚上的交流电压信号,再进行真有效值运算实现简易交流电压表-True RMS computing simple AC voltmeter AC voltage signal the sampling PA0 (ADC_0) pin, then
jiandanyouxiaozhi
- 最简单的有效值计算 计算结果误差为0.02,可以使计算变得很容易。-The most simple RMS calculation calculation error is 0.02, can make the calculation becomes very easy.
demo3
- DSPAD采集算法C6000使用浮点型处理器对AD数据进采集并计算有效值DDS的使用-DSPAD acquisition algorithm C6000 floating point processor into the collection of AD data and calculates the RMS DDS use
DSPBasedDigitalControlOfOnlineUPS
- 本文介绍了一种控制对象以中小型UPS为模型的、基于TMS320F240的数字化控制平台的样机实验系统。经对比系统采用了单极性调制的SPWM方式,并根据核心处理芯片的各类资源给出了一套具体的软硬件数字化实现方案。系统硬件部分主要包括输出电压、输出电流、市电频率/相位等各类信号的采集和处理,以及输出PWM信号的隔离、驱动等。系统软件部分则包括UPS各种系统功能的实现,其中主要研究了软件锁相环(市电跟踪)、有效值调节、各类保护、PWM波的生成、闭环控制等的实现。-This article descri
3KW-eV-net-design
- 利用TMS320LF240系列,采用有效值外环、瞬时值内环的控制方法来保证逆变器良好的输出波形-The TMS320LF240 series, using the effective value of the outer ring and the instantaneous value of the inner loop control method to ensure that the inverter output waveform
msp430-lcd1602
- 12M晶振msp430测量交流电压,采用lcd1602显示,直接显示其有效值-12 m crystal oscillator msp430 measuring ac voltage
AD7799PDF
- AD7799/AD7798 特性: RMS 噪声(有效值噪声): 在 4.13HZ 转换率下紧为 27nV(AD7799). 在 16.7HZ 转换率下为 65Nv. · 低 功 耗 ,典型为 300uA · 内 置 1 一 128 增益的低噪声可编程仪表放大器 · 内 置 时 钟振荡器,省去了外接晶振 · 低 非 线 性度:0.0015 · 内 设 自 校准电路 · 带 有 SPI 数据接口,可以方便地与 DPS 或者 MCU 连接 · 50 H
FHZPIC
- 设计一款基于PIC单片机的力(压力)检测、显示及电机控制系统,实现力的检测与存储、显示以及电机的控制,选定一种通讯方式与电脑进行通讯,将测得的数据传输给电脑。。实时对力进行监测与显示,可以设定一个阈值,正常情况要求电机正传,当所测得的力大于所设定的阈值时电机反转一段时间,当所测得的力恢复小于设定值时电机恢复正转。力的测量由三个力传感器测得,取三个传感器所测值中的最大值为测量的有效值。电机为两个。项目要求检测范围为0~500N,检测精度1 。 电源自选。 技术要求: 1. 设计检测范
smoke_inspect_two
- 有效值检测电压降用matlab来编程实现分析-RMS detection voltage drop using matlab programming analysis
DSP-TEST
- DSP电表工程里面有效值和功率算法的仿真程序。-DSP and power meter project which RMS algorithm simulation program.
Desktop
- dspic33f AD采样dma功能,求得4路电压有效值,实际项目应用文件 -dspic33f AD sampling dma functions, obtained 4 rms voltage, actual project application files