搜索资源列表
1.LED
- 1.LED cc2430 通过输出端口点亮灯管-1.LED cc2430 lit the lamp through the output port
Lab501-LED
- 最基础的用dm642的实现点亮流水灯的程序，初学很有用!-well dm642
led
- 点亮每一个led灯，让初学者感觉到学单片机的乐趣-Each led lamp light, so that beginners feel the fun of learning MCU
LED
- 如何使用LED循环点亮-How to use the LED lights cycle
I2C
- SMART（MAGIC）ARM2200 试验目的 学习编写I2C驱动及应用程序开发 掌握中断程序的开发流程 试验内容 响应按键，点亮对应的LED 按下按键1（S1）点亮LED1。。。，以此类推，按下按键4（S4）点亮LED4 按下按键15（S15）循环左移点亮LED 按下按键16（S16）循环右移点亮LED 完成上述每一步操作，同时要求把键值通过UART0回传到PC -SMART (MAGIC) ARM2200 purpose of study and p
02
- 利用单片机输出循环点亮LED灯D7~D0-Single Chip LED light output cycle using light D7 ~ D0
myled0321
- 使用的是mini2440开发板，开发工具为ads1.2.包含初始化程序，io口设置程序。点亮led-Using mini2440 development board, development tools for the ads1.2. Including initialization, io port setting process. Led light
SRAMreadwritetest
- 这是用verilog开发的外部SRAM测试程序，编写了SRAM的读和写，当读写值相同则点亮LED。在实际测试中检测是正确的。对调试SRAM的朋友有一定的参考价值-It is the development of the external SRAM with verilog test procedures, preparation of SRAM read and write, read and write the same value when the light LED. In the act
LED
- 类型：驱动 功能：控制led灯的亮灭 1:表示点亮 0：表示熄灭-the led driver to control the led turn on or off
test_1_delay_led
- keil环境下，基于Cortex-M3内核LM3S1601的点亮led灯程序源码-keil environment, based on the Cortex-M3 core LM3S1601 of light led lamp source code
ledflower
- 1.跑马灯设计 设计要求：控制8个LED进行花式显示，设计4种显示模式：S0，从左到右逐个点亮LED；S1，从右到左逐个点亮LED；S2，从两边到中间逐个点亮LED；S3，从中间到两边逐个点亮LED。4种模式循环切换，复位键(rst）控制系统的运行与停止- 1. runs the lantern to design <dnt> the </dnt> design requirements: Controls 8 LED to carry on the floral f
5
- 跑马灯的设计 控制16个LED进行花式显示，设计4种显示模式：S0，从左到右逐个点亮LED；S1，从右到左逐个点亮LED；S2，从两边到中间逐个点亮LED；S3从中间到两边逐个点亮LED。4种模式循环切换，复位键控制系统的运行与停止。 输入：连续脉冲，逻辑开关；输出：LED灯。 -Marquee design for artistic control of 16 LED display, designed four kinds of display modes: S0, from
keyProcess
- 按键则点亮LED灯，8路指示灯接p0口,试验演示-Button will light up the LED lamp, 8 light then p0 mouth, test shows
arm-led
- ARM汇编程序，点亮ARM板上的LED，供初学者参考，包括ARM汇编的简单格式-ARM assembler, ARM board LED light
lab5
- 实现点亮功能的嵌入式程序，点亮led，建立点任务，依次点亮a,b两个led，再后输入熄灭-Embedded procedures to achieve light features, light led, to establish point task, in turn lit a, b 2 led, after further input off
AVR_Timer0_Compare
- AVR单片机ATmega16的定时器工作在比较模式，时间到将点亮LED-AVR Microcontroller ATmega16 timers work in comparison mode, the time to light the LED
led(ICC)
- 8种LED点亮模式(ICC) -8种LED点亮模式(ICC)8种LED点亮模式(ICC)
eclipse_leds
- eclipse环境下点亮LED，适合初学者-eclipse environment lit LED, suitable for beginners
GPIO_INT
- 程序正常运行时，熄灭LED指示灯 当按键按下时·触发中断，点亮LED指示灯。按键放开后 又熄灭LED指示灯-Program during normal operation, off LED indicator when the button is pressed interrupt, lit LED lights. LED indicator light turns off after button release
mini6410
- mini6410 最简单的点亮led灯的裸机程序。 cpu型号为三星的s3c6410-mini6410 the simplest bare light led lamp program. Samsung s3c6410 cpu model