搜索资源列表
control_system
- 该系统是双馈发电机转子侧的变流器控制电路,虽然不是很完善,有一定得参考价值。-The system is doubly-fed generator rotor side converter control circuit, although not perfect, there must be reference value.
CF卡转大口IDE的电路原理图
- CF卡转大口IDE的电路原理图,不是很详细。-CF card to IDE Sandy circuit schematic diagram is not very detailed.
ne555电路大全
- ne555电路大全.doc
LM317中文资料_引脚功能_应用电路
- LM317中文资料_引脚功能_应用电路.doc
huawei
- 华为技术资料(PCB布线规范\刚性PCB检验标准\模拟电路\通信技术概论等)-Huawei Technical Information (PCB wiring specification \ rigid PCB test \ analog circuit \ Introduction to Communication Technology, etc.)
exm_5_1
- RC充电电路仿真模型,可以看到曲线变化,初学者可以参考-RC charging circuit simulation model, we can see that curve of change, learners can refer to
HighConvert_Pwm
- 1.本文对一种高效的升压式PWM 变换电路作了分析研究 对开关状态的切换效率高 采用双零软开关工作,大大降低了开关损耗, 提 高了电路的转换效率. 2.该电路在高频的开关电源、逆变器等电力电子电路上有很大的实用价值, 可以提高电路的转换效率. -1. In this paper, an efficient step-up PWM conversion circuit analysis study on the switch to switch the state of high effi
usb_cvt_tool_0.1
- 该工具用于数字电路仿真中的usb数据文件转换: 1.可以把11比特的令牌包数据(crc5)或者任意字节的数据包数据(crc16)转换为可以作为仿真输入的dn dp文件。 2.可以根据仿真接收到的dn,dp数据,解析得到接收的真正11比特令牌包数据或者数据包数据。 3.此为0.1版本,后续的版本更新会让该工具更完善。-The tool for digital circuit simulation usb data file conversion: 1. Can be 11-bit to
FPGA_and_CPLD_VHDL_GB
- VHDL数字电路设计的电子书,很好的学习材料-VHDL digital circuit design of e-books, very good learning materials
clockunit
- 便于单片机简单使用时钟功能的,对于初学者特别有用,只需要稍微懂得电路,了解做个电子时钟原理即可-Simple and easy to use single-chip clock function, particularly useful for beginners, require only a slight circuit to understand, understand to be a principle of the electronic clock to
gongfang
- 这是我收集的功放电路,请大家看看。如果喜欢的可以下。-This is my collection of power amplifier circuit, Please take a look at. If you like to make.
11_logic_analyzer(1)
- 本文介绍射频电路测试原理, 测试仪电路等.-This article describes the principles of RF circuit testing, circuit tester and so on.
matlababoutrf
- Matlab射频电路设计-理论与应用(光盘)-Matlab RF Circuit Design- Theory and Applications (CD-ROM)
445
- 数字音乐盒 (1) 硬件电路中用P1.0~P1.7控制按键,其中P1.0~P1.3扫描行,P1.4~P1.7扫描列。 (2) 用P0.0~P0.7,P2.0~P2.7控制LED,其中P0.0~P0.7控制七段码a,b,c,d,e,f,g,用P2.0~P2.7为数码管位选信号。 (3) 用,P2.0~P2.2作为LCD的RS,R/W,E的控制信号。用P0.0~P0.7作为LCD的D0~D7的控制信号。 (4) 用P3.7口控制蜂鸣器(J2,J4断开,J3短接)。 (5) 电路为
LPC2400
- lpc2400入门,以smartarm2400为例介绍,详细讲诉了lpc2400的外围电路结构-LPC2400 entry to smartarm2400 introduced as an example, to speak at length about the LPC2400 v. external circuit structure
MCS51
- GPS与单片机开发资料,内有GPS输出格式,单片机与GPS接口电路。-Single-chip GPS with the development of information, there are GPS output format, Microcontroller and GPS interface circuit.
ControlOfLEDArray
- LED汉字显示屏控制电路部分的程序代码。接收来自PC机的串口数据,显示出汉字或图形。-Chinese LED display control circuit part of the program code. Receive messages from PC-serial data, showing that the Chinese characters or graphics.
FIFO1
- FIFO存储电路的设计与实现,用verilog实现fifo的参考设计-FIFO memory circuit design and realization of the realization of fifo with Verilog reference design
VHDL_digital
- 《数字系统设计与VerilogHDL》 阐述数字系统设计方法,重点对用vhdl设计开发常用的数字电路和数字系统进行具体阐述,配合大量设计实例。-err
CO2_SENSOR
- 基于红外传感器的CO2气体检测电路设计,文章详细介绍了红外CO2传感器的特性,内含电路原理图,以及程序流程图,需要的朋友可以看看.-Based on the infrared sensors of CO2 gas detection circuit design, the article introduced in detail the characteristics of infrared CO2 sensor, including circuit schematics, as well as