搜索资源列表
Steering-engine-adjustment
- 用于智能车舵机调整中值或其他角度的值得实用程序 128/IDE-For intelligent vehicle steering gear adjusting median or other angle worth utility program
HCS08--smart-car-
- 自循迹智能小车,使用电磁信号巡线,通过电感检测赛道中间的磁导线,使用飞思卡尔HCS08单片机控制舵机、电机-Freescale HCS08 MCU intelligent car Templates
chengxu
- 摄像头,电机,舵机 调试程序,自己改的,大家可以做个参考,作者水平有限,还请大家自己思考并进行取舍-OV7620,moter, duoji and adjustment.please you make the good and waste the bad, I hope that can help you, thank you.
20150128
- MSP430单片机的舵机控制模块程序,在IAR开发环境下实现。-MSP430 MCU steering control module program, implemented in the IAR development environment.
servo
- STM32驱动舵机程序,如果舵机不动需要在IO口和信号线之间串联一个10K电阻-STM32 driver steering program, if the steering gear real need between IO port and the signal line is connected in series with a 10K resistor
car
- 智能小车入门。蓝牙+舵机+超声波+安卓手机遥控源码-Smart car started. Bluetooth+ steering+ Ultrasonic+ Android phone remote source
51-KZ-9G
- 使用51单片机控制辉盛9G舵机,通过控制信号占空比,用按键控制舵机分别反向转动。-Use 51 SCM Fraser 9G servos, by controlling the duty cycle signal, with buttons to control the servo reverse rotation, respectively.
motorctrl
- 51单片机控制多路舵机,用定时器产生pwm波,可以用串口给它发数据控制-51 microchip controls multi servos.
SmartCarCode
- TSL1401线性CCD采集的赛道信息对舵机进行方向控制和欧姆龙编码器采集的脉冲进行速度控制。控制器为MK60DN512VLQ10,IDE为IAR for arm。内含PID控制算法等-Track information collected TSL1401 linear CCD direction of servo control and Omron pulse encoder acquisition speed control. Controller MK60DN512VLQ10, IDE f
PWM
- 舵机PWM控制程序 刚写的一个PWM程序刚在车上调试完毕,控制舵机蛮不错的!-PWM servo control program just wrote a PWM program just completed commissioning in the car, control servos pretty good!
duoji
- 舵机资料大全!!! 帮助新手快速学习舵机知识-Sourcebook steering servo knowledge to help novices learn quickly
Steering-button-control-program
- 51单片机 利用按键控制舵机正反转 程序-51 mcu to control the use of servo reversing SCM program
PWM(2)
- xs128 PWM波 电机舵机控制 加速减速 左右摇头-xs128 motor
duojishangweiji
- 主要完成多级和控制中心的通信,通过上位机界面代替控制中心控制舵机的相对动作-Mainly to complete the multi-level communication and control centers, control servo control center instead of through the PC interface relative movement
sun-light-automatic-tracking-system
- 本文详细介绍了以MG996舵机控制为核心,以STC12C5A08S2做控制芯片,根据M-87获取的相关数据通过按拟合的太阳偏转公式寻找太阳的大致方位,再根据感光模块的相应光强变化进行精确调整,将感光追踪模式与日历追踪模式相结合,以实现运行过程中的自矫正,同时能够根据外界环境判断目前运行状态,做出相应操作最终完成一套能在无人值守环境下自动运行的太阳光源自动追踪系统-This paper introduces the MG996 servo control as the core, STC12C5A
Gen-PWM-With-UI
- 通过ni硬件设备,输出pwm波,调节其占空比和频率控制舵机-Through the ni hardware device, output PWM wave, adjusting the duty ratio and frequency control of steering gear
201
- STM8单片机按键进入中断,中断中调整舵机角度。-STM8 microcontroller interrupt control steering gear case
203
- STM8单片机,控制舵机,左向旋转至水平,然后右向旋转180度后复位。- STM8单片机,控制舵机,左向旋转至水平,然后右向旋转180度后复位。 STM8单片机,控制舵机,左向旋转至水平,然后右向旋转180度后复位。 STM8 microcontroller, servo control, turn left to right, and then to rotate
xunji
- 本程序是基于STC单片机的红外循迹的简单程序,含有左、右舵机的程序(使用的是舵机)。-This procedure is based on STC microcontroller infrared tracking simple procedure, with left and right steering program (using the steering gear)。
20-5_servo1
- 舵机调试程序,C8051F040,舵机控制信号管脚,为P0.7管脚,系统时钟为24500KHZ/8=3062.5KHZ,周期为20ms,则频率为50HZ,则tmph+tmpl=61250可以保证产生50HZ PWM.-Steering debugger, C8051F040, servo control signal pins for the P0.7 pin, the system clock is 24500KHZ/8 = 3062.5KHZ, a period of 20ms, the f