搜索资源列表
等精度数字频率计
- 等精度数字频率计,大连理工大学创新学院,看看吧-And other precision digital frequency meter, Dalian University of Technology Innovation Institute, take a look at it
51单片机实现频率计的程序
- 51单片机实现频率计的程序,产生10个频率。不同频率的计数值:0,100,200,300,400,500,600,700,800,900HZ-The 51 MCU frequency of program
设计一个数字频率计
- 以单片机为核心,设计一个数字频率计,进行频率的自动测量,并用12864液晶屏的第一行显示“数字频率计”,第二行显示设计都姓名和学号,第三行显示测量的频率值(单位:HZ)。 基本部分:数码管显示被测信号的频率,测频范围为1HZ~500KHZ。 发挥部分:扩大测频范围为1HZ~1MHZ。 (2)要求:完成该系统的硬件和软件的设计,在Proteus软件上仿真通过后,提交一篇课程设计说明书。
数字频率计
- 数字频率计是一种基本的测量仪器,它被广泛应用于航天、电子、测控等领域。采用等精度频率测量方法具有测量精度保持恒定,不随所测信号的变化而变化的特点
频率计
- Verilog和VHDL联合编写的频率计
数电课程设计数字频率计.doc
- 数电课程设计数字频率计.doc
数电课程设计数字频率计.doc
- 数电课程设计数字频率计.doc
430f5529低频频率计
- 采用MSP4305529 launchpad 实现 频率测量 有其对应的电路图 以及程序(Using MSP4305529 launchpad to achieve frequency measurement, with its corresponding circuit diagram and procedures)
8位数字显示的简易频率计
- (1)能够测试10HZ~10MHZ的方波信号; (2)电路输入的基准时钟为1HZ,要求测量值以8421BCD码形式输出; (3)系统有复位键; (4)采用分层次分模块的方法,用Verilog HDL进行设计,并对各个模块写出测试代码; (5)具体参照说明文档(包含源代码,仿真图,测试波形,详细的设计说明)(A square wave signal capable of testing 10HZ~10MHZ; (2) the reference clock input by the ci
4位频率计
- 基于51单片机的4位数字频率计的软件设计(digital frequency meter)
Simple frequency meter
- 简易频率计 采用测频和测周法计算高低频的一个程序(Simple frequency meter)
Simple frequency meter2.2
- 简易数字频率计采用了测频和测周法实现频率的测量(Simple frequency meter)
数字频率计
- C语言写51的简易频率计,比较见到那常见,范围到100k(C language to write a simple frequency meter 51, compared to see that common, ranging from 100K)
shuzipinlvji
- 数字频率计msp430F169完成的部分(Digital frequency meter msp430F169 completed part)
CPLD
- 数字频率计在FPGAEP4CE10F17C8上的功能实现和运用(Application of digital cymometer in FPGA)
频率计
- stm32F103测量方波频率,采用外部中断的方法(The stm32F103 measures the square wave frequency using an external interrupt method)
cntf
- 实现在FPGA上的频率计,用VHDL预言实现,可以显示在六位数码管上,范围为1khz至50Mhz(Frequency tester by FPGA)
FMT
- 基于vhdl设计的数字频率计,后面还加了个与fpga通信的模块(Digital frequency meter based on VHDL design, and later added a module to communicate with FPGA)
plj
- 2秒闸门时间频率计,以及一个分频器,使用FPGA及verilog语言实现(2 second gate time frequency meter)
等精度数字频率计
- 可以测量1HZ-150MHZ矩形波(其他波形需整形后输入)信号,误差<0.01%,串口输出NC和NX值。(1HZ-150MHZ square wave can be measured (other waveform needs to be shaped after the input) signal, error <0.01%, serial output NC and NX values.)