搜索资源列表
51_8255_8253_74hc138
- 51单片机控制8255,8253,74hc138实现流水灯交通灯以及对方波的二分频-51 single-chip control 8255 8253,74hc138 achieve light traffic lights and the other wave of the two frequency
jiaotongdneg
- 交通信号灯 本程序设计中用到了8253,8255,8259三个芯片。利用8253分频产生0.1S的时钟,8255连接LED灯输出,利用8259产生中断,控制交通灯的状态。-Traffic lights used in the design of this program 8253,8255,8259 three chips. The use of 8253-Divider 0.1S clock, LED light output 8255 connected by 8259 to gener
dianzishizhong
- 该系统是一个简单的利用8253定时器、8255可并行通信接口和中断控制器8259设计的电子时钟系统,在该系统中设有一个启动键,启动键未按下时,显示初始化界面“HELLO”;当按下启动键时,8253定时器开始计时(8253的初值为10000,接1MHz的脉冲,即当8253计满100时正好是1S),当计时计满100时,8259便产生一次中断,在LED显示器便显示系统预先设计好的初始值“23.59.55”便开始从秒位开始加1,当加到10S时,10s位加1,加到60S时分位加1,同时秒位清零,同时怎加到
汇编关于红绿灯代码
- 基于8279、8253、8255、8259芯片的汇编代码,作用为显示红绿灯及相应的数目管显示,计时总数为十秒。
汇编_电子表
- 基于8253、8259芯片的电子表,语言为汇编。实现为在八位数码馆上显示时、分、秒,逢60进一
微机原理实验报告(硬件)
- 实验1 存储器读写实验 实验2 简单I/O口扩展实验 实验3 8255并行口实验 实验4 8253定时器/计数器接口实验 实验5 8259中断控制器实验
8255traffic-lights
- 用8255控制发光二级管,8253延时,实现简单的信号灯仿真。-8255 control with light-emitting diodes, 8253 delay, to achieve a simple signal simulation.
82538255
- 用汇编语言编写的8253和8255以及中断的综合应用-Prepared by using assembly language 8253 and 8255 as well as the interruption of General Application
STC12CA60S2_KEIL3
- STC12C5A60S2+ 8253+ 串口 + 定时器+AD ,都已调通 可以直接移植。-8253+ STC12C5A60S2+ serial+ timer+AD, can be transferred directly to the transplant.
time1s
- 8253定时1秒asm源文件+proteus仿真电路图。-8253 Timer 1 second asm source file+proteus circuit simulation.
Application
- 一种应用系统外扩展接口芯片8255A.8253组成的微机系统接口的思路-The Application of a Microcomputer System Interface Based on External Expansion Interface Chip 8255A.8253
CourseDesign_StepMotor
- 基于80x86CPU为核心控制器的具备基本I/O接口功能的硬件电路系统原理图设计、PCB电路设计和软件编程设计。基本I/O接口电路包括:锁存器、缓冲器、地址译码器、8255接口、8253接口、A/D(D/A)转换电路、串行接口电路等;软件功能要求完成基本I/O接口电路控制和串口通信功能调试。-Based on 80x86CPU as the core controller with the basic I/O interface function of the hardware circuit
5
- 8253 通道 0 工作在方式 0(脉冲计数产生中断),由按键产生单脉冲接入 CLK0、令计数初值为 0FH, 手动逐个输入单脉冲,编程在计算机屏幕上显示计数值,并用逻辑笔观察 OUT0 的状态,键盘有键按下时 返回 DOS。-8253 channel 0 0 work in way (pulse counting the interrupt), single pulse generated by the key access CLK0, counting the initial val
微机控制的频率测试仪
- 通过8253和8255两个芯片来测试频率,最后测出来的频率误差在1hz到2hz之间,详细情况请见源代码。(Through 8253 and 8255, two chips to test the frequency, and finally measured frequency error between 1Hz to 2Hz, in detail, see the source code.)
汽车控制系统
- 汽车信号灯控制系统 单片机实现摘要:随着汽车制造技术及电光源技术的发展而逐步完善的。它经历了机油(或煤油)灯、乙炔气灯到电光源灯的发展历程。现代汽车信号灯灯具已经开始使用发光二极管(LED)技术以及光导技术,这是信号灯灯具的一次飞跃。现在我们就是利用微机原理的知识用8088,8255,8253等几种芯片来控制汽车的信号灯。(A summary of the realization of the single chip microcomputer for the control system of
微机原理 8086 交通灯 proteus仿真
- 8086交通灯,用8255控制动态显示数码管来作为红绿灯的秒数,用8253作为计数器(8086 traffic lights, using 8255 control to dynamically display the digital tube as the number of seconds of the red and green light, and use 8253 as a counter)
8051双机通信简例
- 这是按单片机(Microcontrollers)是否提供并行总线来区分的。总线型单片机普遍设置有并行地址总线、 数据总线、控制总线,这些引脚用以扩展并行外围器件都可通过串行口与单片机连接,另外,许多单片机已把所需要的外围器件及外设接口集成一片内,因此在许多情况下可以不要并行扩展总线,大大减省封装成本和芯片体积,这类单片机称为非总线型单片机。(This is based on whether a single chip computer (Microcontrollers) provides a
微机原理
- 利用定时器 8253 和外扩展的键盘—显示模块,实现时钟显示及时间设置功能: 1)时钟显示内容为“分:秒”,即“MM.SS”; 2)P 键用来启动时钟设置,通过键盘上的数字修改时间,参数在修改过程中 处于闪烁状态,闪烁频率 2Hz(Using timer 8253 and extended keyboard display module to realize clock display and time setting function: 1) the clock display cont
微机原理综合设计实验-数字电压表A.rar
- 利用ADC0809采集电位器的电压值,将采集的电压值通过8255显示在七段数码管上,显示数据保留小数点后2位,利用8253定时数据更新,每隔0.5秒数据更新一次。扩展要求:具有设置报警阈值功能,当超过阈值时,点亮一个LED灯。(Using ADC0809 to collect the voltage value of potentiometer, the collected voltage value is displayed on seven digital tubes through 825
实验四前三题
- 1、8255 芯片初始化 (1) 分析原理图,计算 8255 芯片和 8253 芯片在 IO 空间中各内部寄存器的端口地址,修改 Demo 程序(main.asm 和 INTDemo.asm)中 IO 空间地址的符号定义(xxH)。 (2) 分析原理图中 8255 芯片 PA、PB 和 PC 口的信号传输方向确定各端口的输入及输出状 态,填充源代码框架中 8255 芯片初始化子程序 INIT8255,完成 8255 芯片初始化代码。 (3) 分析原理图中 PC 口的电路功能,完成对 PC 口各信