搜索资源列表
msp430-CC1100-SPI
- MSP430 CC1100 SPI TX RX-MSP430 CC1100 SPI
rf12_code_cn11
- 学习RF12，TX,RX无线通讯产品，主要应用在遥控方面-Learning RF12, TX, RX wireless communications products, mainly used in remote areas
2Tx-2Rx-Spatial-Multiplex
- 介绍了在MATAB中开发的MIMO通信系统的容量、误码率等问题。很适合初学MIMO的研究生或者科研人员-MATLAB simulation for MIMO capacity and BER
F340_uart
- 本程序是通过F340的uart0与PC进行串口通讯的例程，具体实现为当F340收 *从PC传来的数据后将数据原样回发给PC机 ,端口为RX＝P0.5，TX＝P0.4-This program is through the F340' s uart0 serial communication with PC for a routine, concrete realization of the closing* When the F340 data coming from the PC a
rx
- nrf2401无线 计分牌演示程序\接收端代码，是单片机C语言程序，通过模块NRF实现无线计分，这是接收端程序-nrf2401 Wireless Wireless scoreboard demo \ receiver code, microcontroller C programming language, through the wireless module NRF points, which is the receiver program
q6assign2final
- Simulation of Rayleigh fading channel : 2,4 & 8 Rx Antennas & BER calc
ofdm-Rx
- Matlab Code for OFDM Reciever
2p4-rx
- 2.4 wireless assembly code
can-rx-and-tx
- can信息收发代码，简单实用！适用于初学者！-can receive and trammit codes.it is simple and good！
qpsk-tx-rx
- qpsk transmitter a receiver, in design to simulink with AWGN,noise.
dqpsk-tx-rx
- DQPSK, design of an transmitter and and receiver with AWGN, noise.
EXAMPLE4.15
- PIC16887A单片机一个双机通信，2个单片机异步串行通信接口相连方式为：RX和TX交叉对接，左边的单片机U1，每按下按键S1就发送一个字节数，从0x20开始发送，每送一个数据，此数加1.发送的同时在D口上输出。右边单片机U2为接收状态，采用中断方式，如有接收中断，则进入中断，将接收到的数直接在D口上输出-PIC16887A a two-machine communications microcontroller, two asynchronous serial communication i
search-for-the-serial-communication-
- 本程序是通过F340的uart0与PC进行串口通讯的例程，具体实现为当F340收PC传来的数据后将数据原样回发给PC机 ,端口为RX＝P0.5，TX＝P0.4-Ways to search for the serial communication program
TX-RX-TEST
- 24L01程序，好用哦，基于msp430-24L01 program, easy to use Oh, based on the msp430
chipscope_Tx-Rx
- chipscope analysis of mini uart module including counter for spartan 3e
TestNTC
- 计算被测量电阻。只做比较，不作计算。 计算公式:Rx = Rf * (Tx/Tf) Rx为被测电阻 Rf为已知电阻，Rf=10K Tx为被测电阻对电容C放电的计数值，为16位数 Tf为被测电阻对电容C放电的计数值，为16位数 查温度特性表(NTC型号为:CWF2-473F-3950K,大亚科技制造): 下限温度5摄氏度时电阻为121545.44欧,即121.54544K 换算为:Tx/Tf=Rx/Rf=12.154544 扩大1000倍后结果
xianlutongduanqi
- 线路通断检测器的设计： 1．用压电陶瓷蜂鸣片作为电声元件。 2．用两根导线作为测试探针 3．线路通断是通过测试电阻的大小来判断，有以下三种情况： （1）若150Ω<Rx<900Ω，则蜂鸣片不发出声响。 （2）若Rx>900Ω或者Rx<150Ω，则蜂鸣片发出间歇式的滴－滴声响。 以上各临界阻值（150Ω和900Ω），允许误差±10％ 4．＋15V直流稳压电源需要设计。 -Line-off detector design: 1. Piezo
fet140_uart01_19200_2
- MSP430串口0通信，回显收到的字符。波特率19200.-USART0, UART 19200 Echo ISR, XT2 HF XTAL ACLK. Echo a received character, RX ISR used. Normal mode is LPM0,USART0 RX interrupt triggers TX Echo. Though not required, MCLK = XT2.ACLK = n/a, MCLK = SMCLK = UCLK0 = XT2 = 8M
UARTO
- C8051f310串口通信示例程序，采用串口usart1,串口引脚为P0.4和P0.5，波特率115200. 在KEIL下调试通过。-C8051f310 example of serial communication program. Use usrat1, P0.4 and P0.5 on P0 for TX and RX. The BARDRATE is 115200.
RX
- 德州仪器的lm3sxxxx系列处理器的can总线接收程序-Texas Instruments lm3sxxxx series processors can receive the program bus