搜索资源列表
UART-RX-INTRUPPT
- RAM2410串口通讯中，通过用串口中断来接收其他串口发送过来的数据-RAM2410 serial communication, by using the serial port interrupt to receive other data sent over the serial port
Link-a-System-Level-OFDM-Simulator
- 针对OFDM系统，分成链路级仿真和系统级仿真两个部分。为了降低系统级仿真的复杂度，采用链路级仿真的部分结果。-It contains mainly two parts, i.e. link-level simulator and system-level simulator. Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and
rxusb
- renesas rx usb access to internal bl, linux based
2401_RX
- nRF20L01 RX for 51接收端-nRF20L01 RX for 51
9E5-Rx
- 使用无线收发单片机nodic9E5,来实现信号的发送，最多支持一帧数据发32个字节-Using the wireless transceiver chip nodic9E5, to achieve the signal to send, up to a 32 bytes of data sent
tutorial12
- x10 power line communication is good,to short data communication over powerline.here rf tx and rx software in asm.
MSP430FR57xx_uscia0_spi_09
- Descr iption: SPI master talks to SPI slave using 3-wire mode. Incrementing data is sent by the master starting at 0x01. Received data is expected to be same as the previous transmission TXData = RXData-1. USCI RX ISR is used to handle communi
MSP430FR57xx_uscib0_i2c_04
- MSP430FR57xx Demo - USCI_B0 I2C Master RX single bytes from MSP430 Slave Descr iption: This demo connects two MSP430 s via the I2C bus. The master reads from the slave. This is the MASTER CODE. The data from the slave transmitter begins at 0
uart_top
- UART的verilog代码，tx，rx皆可-Verilog code of UART, tx, rx Jieke
Lab_UART_Correct
- usart rx/tx stm32f10x
UartExample7
- 使用宏定义的某个串口发送数据,包括remap串口，可以用于测试。-stm32fxx usart tx rx for all,with remap
benchmark-tx-rx.tar
- 自己修改过的USRP收发程序，可以实现两个USRP之间的数据传输-USRP receive their modified procedure, can achieve data transfer between two USRP
RS232
- VB RS232 RX and TX data with visual basic source code and using DLL library-Visual RS232 VB program example
fet140_spi0_07
- Descr iption: SPI Master communicates at fast as possible, full-duplex with // SPI Slave using 3-wire mode. The level on P1.4/5 is TX ed and RX ed to P1.0 // and P1.1. Master will pulse slave Reset on init to insure synch start. // Master norma
fet140_uart01_0115k
- // Descr iption: Echo a received character, RX ISR used. Normal mode is LPM0, // USART0 RX interrupt triggers TX Echo. // ACLK = MCLK = UCLK0 = LFXT1 = 8MHz // Baud rate divider with 8Mhz XTAL = 8000000/115200 = 0069 (0045h) // //* An externa
TX-RX-Project
- This an example for Short distance RF data communication.In this project some parameters Temperature,pressure recevived from sensors digitalized and converted to serial , finally transmitted through air . This data received in another unit and the op
si4432-485-rx
- STC10L SI4432 MAX485组成的无线485协议接收端 用于无线485的传输（监控云台控制）-STC10L SI4432 MAX485 protocol consisting of 485 wireless receiver for wireless transmission of 485 (control PTZ control))
01.RF-Interface-Rx-Tx-Auto_Normal
- This the program to communicate between to cc2500 Module in Normal Mode.-This is the program to communicate between to cc2500 Module in Normal Mode.
05.PC-Ctrld-robot_Wireless
- This is the program to communicate between PC and robot with cc2500 Module as TX Rx.
usbDevMuch
- LPC1700芯片USB批量传输源码。只要修改读写信号线以及PID、VID即可立即运行-Source code of USB Driver for LPC1700。You can run it imediatly only if you modify the RX/TX and PID/VID