搜索资源列表
5
- 1：打开IAR开发环境，打开光盘里程序工程。 2：接上仿真器，并把仿真电缆连到CC2430模块上，把程序下载到两个模块上。 3：选择TX发送，选择RX接收 4：LED交替现实发送和接收情况 适用于zigbee开发板-1: Open the IAR development environment, open the disc in the process engineering. 2: connected to the simulator and the simula
3.5GHz--channel-measurements
- 在3.49-3.51GHZ频段内的典型中国城市环境下，地面信号衰落仍服从经典的指数对数分布。在中度误差（σx =10.291）下，路损指数在3.1-3.7之间。半径2公里的小区内，RMS时延在3-4微秒之间；典型的办公室环境中，存在直达径时RMS时延小于0.1微秒。在城市环境中，多径现象很明显，主要由高层建筑物引起，并以簇的方式存在。在城市中低速移动条件下（接收机移动速度小于100 Km/h）某一强径的生存时间通常超过10分钟，但相对到达时间会发生滑动。单一小区内的传播环境具有一定相关性，如果存
S12P-SCI-Tx-and-Rx
- freescale mc9s12p timer example source
1MHZ-code
- * RECEIVER * * CC430 RF Code Example - TX and RX (fixed packet length =< FIFO size)
msp430-CC1100-SPI
- MSP430 CC1100 SPI TX RX-MSP430 CC1100 SPI
rf12_code_cn11
- 学习RF12，TX,RX无线通讯产品，主要应用在遥控方面-Learning RF12, TX, RX wireless communications products, mainly used in remote areas
2Tx-2Rx-Spatial-Multiplex
- 介绍了在MATAB中开发的MIMO通信系统的容量、误码率等问题。很适合初学MIMO的研究生或者科研人员-MATLAB simulation for MIMO capacity and BER
F340_uart
- 本程序是通过F340的uart0与PC进行串口通讯的例程，具体实现为当F340收 *从PC传来的数据后将数据原样回发给PC机 ,端口为RX＝P0.5，TX＝P0.4-This program is through the F340' s uart0 serial communication with PC for a routine, concrete realization of the closing* When the F340 data coming from the PC a
can-rx-and-tx
- can信息收发代码，简单实用！适用于初学者！-can receive and trammit codes.it is simple and good！
qpsk-tx-rx
- qpsk transmitter a receiver, in design to simulink with AWGN,noise.
dqpsk-tx-rx
- DQPSK, design of an transmitter and and receiver with AWGN, noise.
EXAMPLE4.15
- PIC16887A单片机一个双机通信，2个单片机异步串行通信接口相连方式为：RX和TX交叉对接，左边的单片机U1，每按下按键S1就发送一个字节数，从0x20开始发送，每送一个数据，此数加1.发送的同时在D口上输出。右边单片机U2为接收状态，采用中断方式，如有接收中断，则进入中断，将接收到的数直接在D口上输出-PIC16887A a two-machine communications microcontroller, two asynchronous serial communication i
search-for-the-serial-communication-
- 本程序是通过F340的uart0与PC进行串口通讯的例程，具体实现为当F340收PC传来的数据后将数据原样回发给PC机 ,端口为RX＝P0.5，TX＝P0.4-Ways to search for the serial communication program
TX-RX-TEST
- 24L01程序，好用哦，基于msp430-24L01 program, easy to use Oh, based on the msp430
TestNTC
- 计算被测量电阻。只做比较，不作计算。 计算公式:Rx = Rf * (Tx/Tf) Rx为被测电阻 Rf为已知电阻，Rf=10K Tx为被测电阻对电容C放电的计数值，为16位数 Tf为被测电阻对电容C放电的计数值，为16位数 查温度特性表(NTC型号为:CWF2-473F-3950K,大亚科技制造): 下限温度5摄氏度时电阻为121545.44欧,即121.54544K 换算为:Tx/Tf=Rx/Rf=12.154544 扩大1000倍后结果
fet140_uart01_19200_2
- MSP430串口0通信，回显收到的字符。波特率19200.-USART0, UART 19200 Echo ISR, XT2 HF XTAL ACLK. Echo a received character, RX ISR used. Normal mode is LPM0,USART0 RX interrupt triggers TX Echo. Though not required, MCLK = XT2.ACLK = n/a, MCLK = SMCLK = UCLK0 = XT2 = 8M
UARTO
- C8051f310串口通信示例程序，采用串口usart1,串口引脚为P0.4和P0.5，波特率115200. 在KEIL下调试通过。-C8051f310 example of serial communication program. Use usrat1, P0.4 and P0.5 on P0 for TX and RX. The BARDRATE is 115200.
Link-a-System-Level-OFDM-Simulator
- 针对OFDM系统，分成链路级仿真和系统级仿真两个部分。为了降低系统级仿真的复杂度，采用链路级仿真的部分结果。-It contains mainly two parts, i.e. link-level simulator and system-level simulator. Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and
tutorial12
- x10 power line communication is good,to short data communication over powerline.here rf tx and rx software in asm.
uart_top
- UART的verilog代码，tx，rx皆可-Verilog code of UART, tx, rx Jieke