搜索资源列表
usbasp.2005-07-03.tar
- 使用ATmage8制作的USB下载线，采用软件模拟时序-ATmage8 produced by the use of USB download cable, using simulation software Sequencers
usbvision-0.9.8.2.tar
- 这是一个Linux下的USB摄像头捕捉程序，是一个调用V4L2（Video for Linux 2）非常好的例子。英文介绍为：This is a driver for the USB video bridge USBVision from Zoran/Nogatech, a USB-only cable used in many \"webcam\" devices. It supports streaming and capture of color or monochrome video v
spp_dev_a
- BLUETOOTH UART/USB 通信(SPP,Cable Replacement)Master端源代码.-BLUETOOTH UART / USB Communication (SPP. Cable Replacement) Master-source code.
spp_dev_b
- BLUETOOTH UART/USB (SPP CABLE REPLACEMENT)SLAVE端源代码.(开发环境,BLUELAB362)-BLUETOOTH UART / USB (SPP Cable REPLACEMEN T) SLAVE-source code. (development environment, BLUELAB362)
HID1_11
- Universal Serial Bus (USB) is a communications architecture that gives a personal computer (PC) the ability to interconnect a variety of devices using a simple four- wire cable. The USB is actually a two-wire serial communication link that runs
v4l2spec-0.23
- 这是一个Linux下的USB摄像头捕捉程序，是一个调用v4l2 （Video for Linux 2）非常好的例子。英文介绍为：This is a driver for the USB video bridge USBVision from Zoran/Nogatech, a USB-only cable used in many \"webcam\" devices. It supports streaming and capture of color or monochrome video
USBbyteblaster
- USB ByteBlaster Cable 安裝指南
ARS_Code
- I purchased an Ultimate Arduino Microcontroller Pack (you can order the pack online at Makershed or buy it at your local RadioShack). The pack comes with an Arduino UNO and ton of components. It would probably be cheaper to buy components as I need t
library
- 脱机打印，首先都是要把gcode文件放到SD卡上，方法一是在电脑的软件里选择SD卡上的文件开始打印，然后就可以拔掉USB线了（当然不拔也可以，随便你。）；方法二是把要打印的gcode文件重新命名成init.g，放在SD卡的根目录下，重新启动打印机（按reset按键或者断电重新上电都可以），机器就自动开始打印init.g这个gcode了。-There are two ways for offline printing, first of all put gcode file on the SD c
DS1307
- 通过串口数据设置可调整时钟程序 1、程序说明： 该例程演示了如何通过串口数据设定时钟,采用数码管显示。 2、 操作： 1、该串口1可以设置为通过USB口输出或者通过DB9口输出。 如果使用USB输出，请使用USB线将开发板连接至电脑， 如果使用DB9输出，请使用DB9直连线将开发板的J25插座连接至电脑. 同时将跳线插座J28跳到TxD1和RxD1. 打开STC-ISP下载软件中的串口助手，选择相应
usbip-x86
- 在本地虚拟出远程的usb设备，解决了usb线缆的局限性，理论可以无限远。使用方法：服务器端挂载usb设备，客户端在远端访问实现远程设备本地化。-In the local virtual remote USB devices, to solve the limitations of the USB cable, the theory can be infinitely far. Method of use: Mount USB server device, client access remote
USB-2.0-TO-RS232-Cable
- USB虚拟串口,STM 32konghxi -USB virtual serial port
bcight
- 进入方法,连接USB电缆到PC,D5亮时,按FUNC,D5闪烁,-Enter method, connect the USB cable to PC, D5 is bright, the FUNC, D5,
oody
- 进入方法,连接USB电缆到PC,D5亮时,按FUNC,D5闪烁,-Enter method, connect the USB cable to PC, D5 is bright, the FUNC, D5,
lattice_usb_ft2232_cable_sch
- Lattice USB FT2232 JTAG Programming Cable Schematic
SR5-SuperSU-v2.82-SR5-20171001224502
- SR5-SuperSU-v2.82-SR5-20171001224502 1. Copy the downloaded SuperSU Zip file to your phone. 2. Copy the TWRP file to the folder where ADB and Fastboot are installed. 3. Turn off your phone,and turn into Fasboot mode 4. Connect your phone to your
axe027
- this is the axe027 drivers usb cable to program picaxe chips
4_nRF24L01test
- nRF24L01测试可以在两块多功能遥控器开发板上验证，一块板子烧录发送的代码，另一块板子烧录接收的代码，同时将接收数据的多功能遥控器开发板通过USB线连接到电脑，在串口终端上可以看到另一块板子通过nRF24L01发送过来的数据。(NRF24L01 tests can be developed in two pieces of multi-function remote control board, a board send code burn, burn received another ba
BeagleBone_Black_Wireless_ShortSpec
- BeagleBone Black Wireless is based on the extremely successful open-source hardware design of BeagleBone Black, a high-expansion, maker-focused, community-supported open hardware computer, created by the BeagleBoard.org Foundation. BeagleBone Blac
FT2232H FPGA下载器Cable
- 用FT2232H实现的GW FPGA JTAG下载器,高速480M USB,下载速度达30Mb/s