搜索资源列表
xilinxusb
- Xilinx usb下载电缆的图纸资料,可直接制版,然后下载Xilinx的ISE软件进行固件升级。制作图纸准确,使用与官方的下载电缆完全一致。-Xilinx usb download cable drawings, direct plate, and then download the Xilinx ISE software for firmware upgrades. Produce accurate drawings, using the official download cable ex
HID1_11
- Device Class Definition for Human Interface Devices (HID). Universal Serial Bus (USB) is a communications architecture that gives a personal computer (PC) the ability to interconnect a variety of devices using a simple fourwire cable.
RG-BT1800-04-bluetooch-module-spec
- 远距离蓝牙模块,模块在空旷场所通信距离达到1800米,广泛得被国防科大、武汉大学等众多科研项目配套使用。 模块可以是用在USB蓝牙,也可以用在串口数据无线传输。其串口模块成对使用,对于外界开发来说,其相当于一根蓝牙串口线。您无需考虑繁琐的蓝牙协议,您只需要简单的配置波特率、主从模式,就可以为您的系统增加一个强大的蓝牙功能,您只需要用您的单片机通过串口发送数据就能实现蓝牙通信。蓝牙模块 远距离蓝牙 工业蓝牙 医疗蓝牙 串口蓝牙 USB蓝牙 性能稳定 性价比高 -Descr iption:
gumstix
- GPIOn - Input from MAX823 (or equiv), normalizing USB +5V into a clean interrupt signal for determining cable presence.
shuttle_usbat
- Driver for SCM Microsystems (a.k.a. Shuttle) USB-ATAPI cable.
yaokong
- 直接烧好程序,拔掉J15的跳线帽,否则免启动模块会干扰。然后在电脑上打开本程序文件夹串口调试助手,设置波特率为1200,如果使用USB转串口,则要选择相应的串口端口,就可以看到结果的了;如果用串口的话,要连接好串口线,并选择COM1。-Direct burn a good program, unplug the J15 jumper cap otherwise would interfere with free startup module. Then turn on the computer
ustdlib
- “usb_host_mouse”测试CPU的作为USB主设备,将USB接口鼠标插入CPU板上的HOST座,连接上255串口线,点击或移动鼠标观察超级终端。注意:JP2跳帽跳至右侧(短接2-3)(UART波特率设置115200 bps,8-N-1模式发送数据)。-As a USB host device, the mouse into the USB port " usb_host_mouse" test the CPU HOST CPU board seat, 255 seri
430AD2
- DM430-L型最小系统板串口测试程序,使用单片机的串口0通过电脑与串口线连接开发板串口座,使用串口调试助手发送数据到系统板 //系统板会将收到的数据再发送到串口调试助手,接收采用中断模块,发送用查询 板载的BSL模块可以通过跳线帽设置为USB转串口模式,笔记本电脑没有串口可以直接代替 开发板的BSL_Config区的RXD和TXD0连接,TXD和RXD0连接即可-DM430-L-type minimum system board serial testing procedures,
SerialPortCommunication_VBNet2
- The serial (COM) port is one of the simplest ways to communicate between a PC and a microcontroller circuit. Most microcontrollers have hardware serial ports and most microcontroller compilers have built-in functions to read from and write to the
unusual_usbat
- Unusual Devices File for SCM Microsystems (a.k.a. Shuttle) USB-ATAPI cable.
gumstix
- GPIOx - Connects to USB D+ and used as a pull-up after GPIOn has detected a cable insertion driven low otherwise. -GPIOx - Connects to USB D+ and used as a pull-up after GPIOn has detected a cable insertion driven low otherwise.
usb_debug
- USB Debug cable driver.
uss720
- USS720 USB Parport Cable for Linux v2.13.6.
shuttle_usbat
- Driver for SCM Microsystems (a.k.a. Shuttle) USB-ATAPI cable.
STM32_ESP8266_WIFI
- 本程序会将WIFI模块发送的数据转发到USART1串口,同时将USART1串口接收到的数据转发给WIFI模块。这样客户就可以通过HL-340的USB转RS232串口线来测试WIFI模块的AT指令了。-The data in this program will be forwarded to the WIFI module sending USART1 serial port, while forwards USART1 receive serial data to WIFI module. So
UART
- //DM430-A型开发板串口接收发送程序,使用单片机的串口0,显示操作通过串口调试助手 //通过电脑与串口线连接开发板串口座,使用串口调试助手发送数据到开发板板 //开发板板会将收到的数据再发送到串口调试助手,接收采用中断模块,发送用查询 //板载的BSL模块可以通过跳线帽设置为USB转串口模式,笔记本电脑没有串口可以直接代替 //开发板的BSL区的RXD和TXD0连接,TXD和RXD0连接即可 //注意使用BSL模块作为USB转串口功能的时候,RTS和TCK跳线帽、DTR
CH340SER
- Driver to connect usb serial cable to windows 7
USBTORS
- USU资料 UT-810 USB 1.1 TO RS232 Cable USB 2.0 TO RS232 Cable