搜索资源列表
BiometricCardiacIrregulaity
- An ECG is used to measure the heart’s electrical conduction system.[4] It picks up electrical impulses generated by the polarization and depolarization of cardiac tissue and translates into a waveform. The waveform is then used to measure the rate an
Electrocardiogram-Signal-Compression-Using-Multiw
- An ECG is used to measure the heart’s electrical conduction system.[4] It picks up electrical impulses generated by the polarization and depolarization of cardiac tissue and translates into a waveform. The waveform is then used to measure the rate an
ansysapdl
- Ansys分析平行版电容器之间的磁场,此磁场为平板之间的传导和位移电流诱导所得。-This problem demonstrates the calculation of the magnetic field induced by both the conduction and displacement currents in a parallel plate capacitor filled with a lossy dielectric.
Numerical-method-conductionMATLAB
- 热传导方程几种差分格式的MATLAB数值解法比较-Numerical method for solving the heat conduction equation of several kinds of difference scheme of MATLAB
2D-Diffusion
- 2d diffusion (conduction heat transfer) code in fortran
2D-Heat-conduction
- 2 Dimensional Heat Transfer simulation (MATLAB CODE)
Keff-=-Ks-3~10
- 薄片移动法计算导热方程,计算浓度场,得到末端凝固位置-Heat conduction equation method to calculate the sheet moves
HAO
- 本文描述的动态行为 并行输入/并行输出直流电流型控制 buck-boost转换器作为multiinput /初步研究 多输出。这个系统的主要应用之一 是集成光伏阵列是什么时候 连接到网格作为可再生能源的来源。的twomodule 变换器由两个相同的buck-boost电路 和直流运行传导模式 (CCM)。-the paper describes the dynamic behaviour of a parallel-input/parallel-output curre
daorechegnxu
- 基于C++的二维稳态导热计算程序,附带程序说明以及matlab的绘图说明-Based on two-dimensional steady-state heat conduction C++ calculation program, with the program descr iption and drawings illustrate matlab
GPRS
- 模块使用说明: 1、产品不震动时,震动开关呈断开状态,输出端输出高电平,绿色指示灯不亮; 2、产品震动时,震动开关瞬间导通,输出端输出低电平,绿色指示灯亮; 3、输出端可以与单片机直接相连,通过单片机来检测高低电平,由此来检测环境是否有震动,起到报警作用-Module USES: 1, the product is not vibration, vibration switch is disconnected state, output, output level green l
PFCBoost
- 介绍了平均电流控制型 PFC Boost 变换器的结构, 分析了其工作原理。 分别采用 Power System 工具箱和考虑电感电流断续工作状态的 C-MEX 文件 S 函数建立了主电路模型,对平均电 流控制型 PFC Boost 变换器进行了仿真。仿真结果表明,与 Power System 工具箱模型相比,基于 C-MEX 文件的 S 函数仿真模型能够准确仿真电流断续工作状态,仿真速度快。设计了电路样机进 行了实验研究,仿真结果与实验结果一致,证明了该方法的正确性。利用该方法
SourceFile1
- fortran code for 2D unsteady heat conduction in a plate
HC_analytical_h
- heat transfer by conduction analytical
HC_test_h
- heat transfer by conduction (compare) analytical numerical
HJ
- 脚踏点焊机输出电压调压控制,单片机通过检测过零点控制可控硅导通脚调整输出电压。-Foot operated spot welder output voltage regulator control, microcontroller through the detection of zero crossing control thyristor conduction pin to adjust the output voltage
STC12C5052AD-Transistor-tester
- 测二极管(包括稳压二极管,发光二极管),三极管(NPN,PNP型自动识别),可控硅等晶体管的极性自动识别,导通压降及hFE等等特性。-Measuring diode (including the zener diode, light emitting diode), triode (NPN and PNP type automatic recognition), silicon controlled transistor, such as automatic identification of
AVR-Transistortester_neu
- 测二极管(包括稳压二极管,发光二极管),三极管(NPN,PNP型自动识别),可控硅等晶体管的极性自动识别,导通压降及hFE等等特性。-Measuring diode (including the zener diode, light emitting diode), triode (NPN and PNP type automatic recognition), silicon controlled transistor, such as automatic identification of
poissonSolver2D(2)
- 2D Finite Difference to solve 2D hear conduction equation using high performance computing.
zuoyetwo
- 利用TDMA和ADI方法求解二维稳态导热问题,采用C语言编程-Use TDMA and ADI method for solving the two-dimensional steady-state heat conduction problem, using C language programming
one-dimension-heat-conduction
- 一维传热程序,适合初学者学习参考,广泛应用于计算流体力学-one dimensional heat transfer program, computational fluid dynamics