搜索资源列表
23_DCMotor
- DCMotor 用于直流电机的控制,适合大家学习dsp-DCMotor for DC motor control, for them to learn dsp
HVPM_Sensored
- 永磁同步电机的DSP控制程序,基于TI公司TMS320F28035芯片,包括电流环和速度环,为磁场定向控制的带传感器程序。-DSP control of permanent magnet synchronous motor program, based on TI' s TMS320F28035 chips, including current loop and speed loop for the field oriented control with a sensor program.
HVACI_Sensored
- 感应电机的DSP控制程序,采用TMS320F28035磁场定向控制技术的有传感器控制。-Induction motor control DSP program, using TMS320F28035 FOC control of a sensor.
HVBLDC_Sensored
- 直流无刷电机的DSP控制程序,基于TMS320F28035芯片,采用有传感器的磁场定向控制技术。-Brushless DC motor DSP control program, based on TMS320F28035 chip, using a sensor field-oriented control technology.
61IC_S1335
- dsp控制电机,主要是控制永磁同步电机的程序-dsp control motors, permanent magnet synchronous motor is to control the main program
3.3.2-DC_Motor
- 这是我们学校的DSP开发板5502上DSP控制直流电机的程序,工程文件齐全,保证可以用,可以实现直流电机运行,电机反向,电机刹车,加减速等功能.-This is our school s DSP development board DSP-controlled DC motor on the 5502 program, project documents are complete, to ensure that you can use, can run the DC motor, the mot
cd4ef1.ZIP
- 采用DSP和FPGA直驱阀用音圈电机驱动控制系统Using DSP and FPGA direct drive valve uses the voice coil motor drive control system-Using DSP and FPGA direct drive valve uses the voice coil motor drive control system
xy7z.ZIP
- 采用DSP和FPGA多电机速度伺服驱动控制平台Using DSP and FPGA multi motor speed servo control platform-Using DSP and FPGA multi motor speed servo control platform
lunwen1
- 基于DSP的一步电机直接转矩控制系统硬件电路设计与实现,基于DSP的一步电机直接转矩控制系统硬件电路设计与实现-there is no translation there is no translation there is no translation
PWM_MotoB
- 1.本示例将演示电机的闭环控制,即以单位时间内的码盘脉冲输出为反馈,以单位时间内 // 欲达到的脉冲数为输入,以变占空比的PWM波为输出。使用的算法为经典的PID控制算法 // 该算法具有实现方便,参数整定容易,控制鲁棒性好等优点。借助我们的串口虚拟示波 // 器软件,用户可以很方便地整定出一套满意的参数。 //2.PID算法要处理的数据不外乎输入与反馈的偏差(做比例运算),本次偏差与上一次偏差 // 的差(做微分运算,离散化以后就是差分运算),所有变差的累积(积分运算,离散
PWM_MotoA
- 1.本示例演示PWM波形输出以控制电机,通过配置,28035的PWM1A和PWM1B将输出频率为10KHZ的方波; //2.28035有多达7个通道14路PWM波输出,在本实验中,我们使用的是PWM1的A路和B路, // 它们分别是GPIO0和GPIO1。-DSP theory and motor control applications
design-and-implementation
- 基于PCI总线和DSP的步进电机运动控制卡的设计和实现-Stepper motor control card based on PCI bus and DSP design and implementation
pmsmVECTORCONTROL
- dsp 控制永磁同步电机,矢量控制,欢迎下载。
Example_280xEPwmTimerInt
- DSP程序,关于直流电机双环矢量控制,CCS编译-dc motor FOC in CCS
wheelchair-DSP_-microcontroller--
- 设计了一种以凌阳公司SPCE061A单片机为语音信息处理器,以DSP为驱动控制器的主从式智能轮椅语音控制新方案。采用SPCE061A单片机进行语音指令的训练、识别和处理,DSP作为驱动电机转动的PWM控制信号发生器,SPCE061A单片机和DSP之间通过SCI接口电路进行通信。详细阐述了智能轮椅语音控制系统各部分硬件结构及系统总体软件实现,重点讨论了电机驱动电路的硬件设计和系统软件流程。实验结果表明,研制开发的智能轮椅语音控制系统能够在语音或手动模式下实现轮椅的多种运动,语音识别正确率高于95
ACI_VF
- 基于IQMATH形式的三相感应电机VF控制的dsp程序- Did you mean: 基于IQMATH形式的三相感应电机VVVF控制的dsp程序 Allow phonetic typing English Spanish Arabic VF co
bldc_hall_sensors
- 无刷直流电机DSP控制,DSP芯片TMS320F2812-DSP control of the brushless DC motor, the DSP chip TMS320F2812
kmotor5
- 此程序运行在5402 DSP平台下,控制步进电机的正转,反转等-This program runs in the 5402 DSP platform, control stepper motor forward, reverse, etc.
MOTOR
- PWM波控制电机的转动程序 DSP的PWM1和PWM2来进行控制 经过了两级放大输出 改变电机转速或转向 -PWM wave control the motor rotation program the DSP PWM1 and PWM2 control after two amplified output to change the motor speed or steering
STEP
- DSP控制步进电机原理 由DSP输出的PWM3~6做为步进电机的4个信号线输入,选了PWM的IO口.-DSP controlled stepper motor principle by the DSP output for PWM3 ~~ four signal line input as a stepper motor, select the IO port of the PWM.