搜索资源列表
iic
- 一个verilog源代码，可用ISE等实现，功能为I2C接口标准建模。-A verilog source code, can be used, such as the realization of ISE, the functional model for the I2C interface standard.
I2C
- 改程序实用PROTUES仿真软件，利用汇编程序编写的I2C程序，说明详细。-PROTUES practical reform process simulation software, using the I2C programming compilation process, a detailed descr iption.
IIC_JPG
- I2C时序图.想通过软件实现I2C总线通讯的朋友一定需要它-I2C timing diagram. Would like to achieve through software I2C bus communication it must be a friend
i2c
- 采用AT90can128单片机的IO口进行twi两线串行接口的数据读写，从差压传感器读取12压力数字值-IO using AT90can128 SCM twi I conducted a two-line serial interface to read and write data from the differential pressure sensor to read the digital value of 12
I2c
- 单片机与IIC的通讯，主要用于单片机与具有iic接口的器件，也可以作为测试使用-SCM and IIC communications, mainly for single-chip iic interface with the device can also be used as a test
I2C_init
- 在通迅程序中,基本上所有的人最开始接触的通迅协议就是I2C或者串口,但是一个合格的电子软件工程师,必须熟悉I2C的标准流程和标准程序包,而不是仅仅是移值.看了这套源码,你可以学习周立功公司的I2C程序标准.-In the communication process, essentially all of the people in contact with most of the communication protocol is I2C or serial port, but a qualif
I2C_receiver
- 自己写的一个i2c slave的模块，verilog，已经通过验证，可以写可以读，希望对大家有用-To write a i2c slave module, verilog, has been validated, you can write can be read, in the hope that useful
ucoszlg7290
- ucos在ARM芯片LPC2210上的移植代码，包括三个任务：中断方式读ZLG7290的按键；基于I2C接口的温度传感器；一个TFT液晶芯片的驱动显示，调试通过。-ucos in ARM transplantation on the LPC2210 chip code, consists of three tasks: reading ZLG7290 interruption of the keys I2C interface on the temperature sensor a TFT
C8051I2C
- 这是一个关于单片机C8051f120的用I2C总线访问外部扩展存储器的C语言程序，非常的实用-This is a study on the use of single-chip I2C bus C8051f120 access to external memory to expand the C language program, that is very practical
I2C_EEPROM
- 用PIC单片机对EEPROM进行读写操作。 按单排按键“1”，程序从从8位拨动开关读入地址（范围0x00～0xFF），并从EEPROM读出该地址的值，地址与数据都显示在液晶屏上。 按单排按键“2”，程序从从8位拨动开关读入地址（保存，作为写入地址），液晶屏提示输入8位数据，此时拨动8位开关，再按一次按键“2”将拨动开关的状态（8位数据）写入之前保存的地址-PIC single-chip EEPROM with read and write operations on. By single
I2C
- This I2C project is a simple program for the NXP LPC2900 family microcontroller using the HITEX LPC2929/39 evaluation board and demonstrating I2C functionality using the onboard SE95 temperature sensor.
tuner
- 89c51控制I2C电视高频头今天成功制作了用89c51控制I2C电视高频头LCD显示。先做好51的最简单系统，然后P3口LCD，P2.0,P2.1,P2.2分别接LCD的R/S，R/W，E。P0.0，p0.1分别接高频头的SCL，SDA。-89c51 TV Tuner I2C control a successful production today with I2C control 89c51 TV tuner LCD display. 51 to do the most simple sy
utils
- 此代码为嵌入式开发中非常有用的几个功能模块 1。flash目录是对flash操作控制 2.ftpfs目录是ftp功能模块 3.i2c目录是i2c的驱动模块 4.memwatch是内存监测功能 5.setnet是网络设置功能 6.subtitle是媒体播放时外挂字幕解析功能。 7.usb是USB模块的自动挂载和卸载功能-This code is embedded in the development of a number of very useful function
i2c
- This code implements the control of the i2c bus with a MC68000 type interface. It is modeled from the M-bus component in certain Motorola uC. The I2C control is done in the component i2c_control and the uC interface is implemented in the component u
WorkSpace
- DS18B20+I2C+串口程序，并且有相应的Proteus的联调图，已测，可运行。还有相应的一些资料。-DS18B20+ I2C+ serial process, and there is a corresponding adjustment plan joint Proteus has been measured, you can run. There are corresponding with some information.
Mars-EP1C6-F_code2
- 此包为FPGA学习板接口实验程序源代码,共包括13个实验程序,有7段数码管,1602液晶显示,12864液晶显示,I2C总线,串口通信,拨码开关等.-The packet interface to FPGA board experimental procedure to study the source code, a total of 13 experimental procedure, there are 7-segment digital tube, 1602 LCD 12864 LCD,
8563
- PCF8563驱动程序.使用ARM2103板子的I2C初始化并读取数据 -PCF8563 driver. ARM2103 using the I2C board initialization and read the data
8051ApplicationCode
- 该程序为基于51单片机的接口和片外应用的代码，在设计51单片机时可供参考，代码包括RS232通信、I2C、SPI、单总线、CAN总线、键盘、LED、LCD、AD/DA等应用。各工程在Keil调试通过，喜欢的朋友可供参考。-The program is based on the 51-chip microcontroller interface and application code, in the design of microcontroller 51 when the reference
430i2c
- ADS1110的读写程序，已经调试好的，可以放心使用。-ADS1110 for reading and writing program, has a good debugging, you can rest assured that use.
DE1_CAMERA
- an example of using a camera modul with i2c